eChapters

Bottom or demersal trawling continues to be one of the most important fishing methods of the world. In India more than 35,230 trawlers of various sizes ranging from 9 to 30 m L_OA with engine power ranging from 45 to 495 hp @ 2000 rpm are in operation. Trawl is a bag net towed through water to filter out fishes, the mouth of which is kept open horizontally by means of a beam or otter boards and vertically by means of floats and sinkers. Horizontal mouth opening is also effected by dragging the net from two boats known as bull trawling or pair trawling. The principle of trawling is the movement of the net under water filtering the water through the mesh in the netting, without either permitting the fish to escape or gilling them (Fig. 1). Trawl net is fabricated using polyethylene netting after cutting and shaping the panels as per the design

Maintaining the quality of fish begins with harvest and carries through the harvest-to- consumption chain. Careful handling of fish and shellfish while harvesting and during transport to the processing plant is critical if the high quality of the product is to be maintained. There are, however, several constraints on handling the fish; the important among them are the bacteriological, chemical and physical processes that cause degradation of fish. The surface of dead fish is an ideal growth habitat for bacteria and the end result of such activity is spoiled fish. Reduction of temperature can prevent the growth of many bacteria that cause the spoilage. Chemical breakdown due to oxidative and enzymatic reactions can lead to off odours and flavours and rancidity. Digestive enzymes can initiate decomposition in the dead fish. Physical factors can enhance the bacteriological or chemical processes: bruising, tearing, cutting etc. can expose fish muscle to more rapid bacteriological growth, cause internal bleeding which darkens the fillets and expose greater surface area for chemical oxidation.

Since fish is a highly perishable item of food, it has to be immediately processed to various products to preserve the quality and to increase the shelf life. Fish requires proper handling and preservation to increase its shelf life and retain its quality and nutritional attributes. The objective of handling, processing and preservation is to control or reduce the spoilage process so that the final product is wholesome and safe for the consumer. Fish and fishery products brought to market in a well-preserved condition will generally command higher prices, both at wholesale and retail levels, and thus give better returns to the fishing operation.

Low temperature preservation by chilling and freezing methods are widely practiced to maintain the quality and freshness of fish and fish products. Chilled storage method, i.e., keeping the fish in the unfrozen condition has only limited shelf life and it will vary between 4 and 20 days depending on the condition and species of fish. In frozen storage also the shelf life is restricted but it varies from few weeks to years. The various factors that affect the frozen storage shelf lives are condition of fish at the time of catch, handling, processing and product development, packaging and glazing of the product, freezing method adopted, frozen storage temperature, stacking methods and transportation techniques. These factors can be put together and can be termed as ‘Product, Processing and Packaging’ (PPP) and ‘Time Temperature Tolerance’ factors (TTT).

Trends in aquaculture and fisheries

Global fisheries have made rapid strides in recent years by establishing its strong hold over increasing food supply, generating job opportunities, raising nutritional level and earning foreign exchanges. These benefits become more important when placed in the context of current challenges in food production, nutritional security, social transitions and growing climate uncertainties. Fish and fishery products are the most traded food commodities in the world accounting for 1% of world merchandise trade in value terms representing more than 9% of total agricultural exports all over world (FAO, 2014). About 38% of the global fish production enters international trade in various forms and shapes, generating an export earning of nearly US$148.1billion with a record import at US$140.6 billion during 2014. Mostly the developing countries that account for over 60% of global fish catch, which has continued to expand at an average annual rate of 8.8% (FAO, 2009 & 2012) and play a major role in the global trade of fish and fish products contributing around 50% of fishery exports in value terms and more than 60% in quantity terms supplied by them (World Bank, 2011). At the same time, demand for fish products are likely to rise as a result of rising populations that are expected to reach 9.3 billion by 2050. Developing countries have a positive trade balance due to their increasing involvement in global fisheries trade. Developing country like India may have higher proportion of population growth but its impressive economic growth over the past two decades has resulted in steady increase in per capita income in real terms that in turn increases the purchasing power of people resulting in increasing demand for food to feed & ensure nutritional security of the population. As a result of which it brought inconsistency in fish consumption pattern across the coastal, marine and hill region.

India has made considerable progress in improving its food security. The agricultural development strategy pursued in the country, particularly since the mid-sixties, is recognized and appreciated world over. The integration of agricultural research with quality education and a properly planned extension education system has been one of the fundamental foundations of this developmental strategy, which also led to revolutions in many other sectors of agriculture and allied enterprises. As a part of this strategy, several programmes of transfer of technology from research stations to farmers’ fields were launched in the country. These included National Demonstration Project, Lab to Land Programme, Operational Research Project and Krishi Vigyan Kendras (Farm Science Centers). The programmes were continuously reviewed from time to time and reformulated for their effectiveness. Presently the Krishi Vigyan Kendras (KVKs) have been recognized as an effective link between agricultural research and extension system in the country (Venkatasubramanian et. al., 2009).

Krishi Vigyan Kendras (Farm Science Centers), an innovative science-based institution, were established mainly to impart vocational skill training to the farmers and field-level extension workers. The concept of vocational training in agriculture through KVK grew substantially due to greater demand for improved/agricultural technology by the farmers. The farmers require not only knowledge and understanding of the intricacy of technologies, but also progressively more and more skills in various complex agricultural operations for adoption on their farms. The effectiveness of the KVK was further enhanced by adding the activities related to on-farm testing and front-line demonstrations on major agricultural technologies.

Introduction

Oxygen uptake in fishes is affected not only by the abiotic factors of the environment but is also affected due to various biotic factors. Works on fish aggregation reveal that oxygen uptake of a fish is changed by the number of fishes mutually participating in respiration which has been demonstrated by various workers. The variation in oxygen uptake when fishes of either similar or different genera or species are kept in an association is known as the group effect. The variation in oxygen uptake due to the group effect is an established fact.

The investigation and approaches of Allee (1931); Schtefanesku (1958); Malyukina et al, (1962); Grigor’eva (1966); Umezawa and Watannbe (1979), Wares II and Igram (1979), Umezawa et al, (1981) Imabayshi and Takahashi (1987), etc. are worth mentioning and regarded as milestones in this field. Allee (1931), Shlaifer (1938); Geyer and Mann (1939), Job (1955); Delco (1963); Uematsu (1971); Parker (1973), Itazawa et al, (1978); Smatresk and Herreid (1980); Kanda and Itazawa (1981); Singh and Munshi (1985) and Jha (1995) have observed that grouping lowers down the oxygen uptake of fishes but the reverse relationship was also reported by Bowen (1932); Schuett (1934), Brett and Sutherland (1965), Umezawa and Kanikawa (1980), Ghosh et al, (1994), Krause and Ruxton (2002), Pandit and Ghosh (2007), Ward and Webster (2016). In due course, different aspects of grouping have been studied by various workers and many terms are proposed accordingly to explain the phenomenon.

Organic Fertilizers and Manures

Farmers have been using organic waste as fertilizers for a very long time. As previously mentioned, the application of O.M. to a soil can have number of beneficial effects on soil structure, C.E.C. and microbial activity. However, organic manures mainly originate from the waste products of animal and plant production and although rich in carbon compounds, they are usually relatively poor in available plant nutrients.

The nutrient content of organic manures varies widely depending on their source and moisture content. Farm yard manure (F.Y.M.) is one of the most common organic fertilizers used. Others are concentrated animal manures, and crop residues such as straw.

Liebig (1840) on the basis of soil and plant analysis deduced the phosphorus requirement of plants. J.B. Lawes conducted series of field experiments to improve the fertilizer value of common sources of phosphorus such as bone meal, apatite, rock phosphate. Lawes (1843) produced super phosphate by treating apatite mineral containing phosphorus with sulphuric acid. He also stated that the phosphorus present in bones of higher animals can be made available by treating with sulphuric acid.

Phosphorus is the second most deficient nutrient in the world. Annual application of phosphorus fertilizers to crops is 36 million tons of which

1.32 m tones are consumed in India. Most of the arable soils in tropical and subtropical regions are deficient in phoshphorus, but the response of crops to phosphorus is uncertain. Phosphorus concentration in plants ranges from 0.1 to 0.4 per cent.

Diagrams and graphs are the effective and attractive ways of presenting data. Widely used diagrams for data presentation are pi chart and bar diagrams. Bar diagrams are also of various types; (i) Simple bar diagram (ii) Component or sub-divided bar diagram (iii) Multiple bar diagram (iv) Percentage bar diagram. The widely used graphical presentation are histograms, frequency polygon and frequency curve.

There are numerous libraries to create charts and graphs in R programming language.

Pie-chart- A pie-chart is a representation of values of variable as sectors of a circle with different colours/shadings. The colours/shadings used for different sectors are indexed at the side of the graph. pie() function is used to create pie chrt in R.

Let us create an exel file names as ‘exp_sports’ which contains the expenditure made (in Rs.) under various sports in a sports club. The name of the sports are cricket, hockey, tennis and football. The names of sports are placed under the column head ‘sports’. The corresponding expenditure (in Rs.) are 7200, 3600, 1800, 1800 and they are placed under the column head ‘expenditure’.

The basic syntax for creating a pie-chart using the R is.

Is it possible to feed a world population projected to reach 8.5 billion by 2030, 9.7 billion by 2050 and exceed 11 billion in 2100? India expected to surpass China as the most populous country in the world within seven years (UN report July 2015). Besides that there is an immense decline in yield and quality over the past three decades may be at the point of diminishing returns (Bouis 1993; Cassman et al. 1995; Flinn and De Datta 1984). Furthermore, the soil is partially under tremendous pressure to sustain yield and production. The excessive and exhaustive agriculture practices have not only declined the soil quality but it’s also reported for different human and animal health issues. Thus, keeping pace with population growth and health safety appropriate soil management practices must be addressed. Now burgeoning population load, declining yield, soil health diminution, and effect on human and animal health arises the opportunity for sustainable soil management to cater the problem at the right time. Figure 1 clearly indicates the tremendous load on soil and subsequent results. Burgeoning increase in population and a load of food production intensification, sustainable soil management will become increasingly important in future. Soil being the powerhouse of the mineral nutrients also retains most living organisms within it. The appropriate soil management practices ensure the critical level of mineral elements which finally come into the human body.

Soil Organic Matter

Soil organic matter plays an important role in the maintenance and improvement of soil properties. It is a dynamic material and is one of the major sources of nutrient elements for plants. Soil organic matter is derived to a large extent from residues and remains of the plants together with the small quantities of animal remains excreta, and microbial tissues. Soil organic matter is composed of three major components i.e. plant residues, animal remains and dead remains of microorganisms. Soil organic matter comprises residues of plants and animals and these compounds occur in soil in close combination with inorganic substances. Animals and plant residues are made up of complex carbohydrates, simple sugars, starch, cellulose, hemicellulose, pectins, gums, mucilage, proteins fats, oils, waxes, resins, alcohols, aldehydes, ketones, organic acids, lignin, phenols, tannins, hydrocarbons, alkaloids, pigments, etc.

The organic matter subjected to microbial decay in the soil comes from several sources like plant remains, forest litter, incorporation of plant tissues, animal tissues, and excretory products. The chemistry of organic matter is very complex, and investigations of the transformations and the responsible organisms have therefore been extremely interesting. The organic constituents of the plants are commonly divided into six categories.

Fruit jelly is an important part of diet of all human being. It is easily digestible, highly refreshing, appetizing and nutritionally far superior to many foods. Today, a wide variety of fruit jellies are consumed in the home, at work place and sport stadium. There has been considerable increase in the consumption of fruit and vegetable jellies in the world during last few years. Jelly is a semi-solid product prepared by boiling a clear strained fruit extract free from pulp after the addition of required amount of sugar, citric acid and pectin. It should contain minimum 65 percent of total soluble solids and minimum 45 percent of fruit portion (Dhawan, 1998). Guava is rich source of pectin and acid content and have thick flesh is preferred for jelly making. For getting good quality jelly, mix under-ripe fruits give better pectin content and ripe fruits provide the flavor. Winter season fruits yield better quality jelly (Singh and Dhawan, 1983). It is a clear or translucent fruit spread made from sweetened fruit (or vegetable) juice and set using naturally occurring pectin. Additional pectin may be added where the original fruit does not supply enough. Jelly can be made from sweet, savory or hot ingredients. It is made by a process similar to that used for making jam, with the additional step of filtering out the fruit pulp after the initial heating.

Jellies are the products used as bread spreads all over the world. These are made from fruits rich in pectin. Guava, because of its rich pectin content, is processed into jelly. Processing of guava into jelly is practiced by processors all over the world. Colouring of jams and jellies has been an age old practices colorants. Great attention is being paid now days to the usage of natural colours in view of the hazards that the synthetic colours pose to human health. Incorporation of carrot resulted in colour improvement over control. Jelly containing carrot as a colouring source was found slightly better than other vegetables. Jelly is a semi-solid product prepared by boiling a clear strained fruit extract free from pulp after the addition of required amount of sugar, citric acid and pectin. It should contain minimum 65% of total soluble solids and minimum 45% of fruit portion (Dhawan, 1998).

Introduction

Commonly available food materials especially dairy products, cereals and fruits are perishable and require processing for long term storage. The methods of food storage has been known from the pre historic times and was mostly based on processing the food into a more stable form with a longer shelf life. Such processes increases the time range of food availability and in many cases improves the taste thereby, cumulatively improving the food value. One of documented method of food preservation is by fermentation and is age old. Other commonly used methods include drying, refrigeration, salting and fermentation (Luck 1985, Paulus, 1985, Christensen et al., 2003, Martindale and Schiebel, 2017).

Flavour and appeal of food has been considered as one of the important factors contributing to the demand of the food. Originally the flavours were largely plant derived, current industrial practices largely utilise synthesis by chemical reactions and subsequent extraction to achieve a uniform quality (Weckerle et al., 2006, Davidovich-Rikanati et al., 2008, Sethupathy et al., 2018). These chemicals referred to as “flavourings” are defined as compounds that enhance the taste, appeal and palatability of food. They are naturally derived or artificially synthesised compounds. Considering that many artificially synthesised chemical flavours might affect the health adversely. Industrial food research has now shifted their focus on flavourings that are naturally available (Cohen et al., 2018). Such naturally occurring flavourings are referred to as bio-flavours (de Billerbeck 2015). The ease of producing bio active compounds from microbial culture extracts has played significant role in industrial food biotechnology (Verachtert et al., 2005).

Introduction

Wine is a very unique fermented beverage. It was an essential part of various religious and cultural ceremonies in ancient civilizations; and continues to be considered as a ‘drink for elite’. The reason is that wine was considered as ‘Gift of God and ‘God’s nectar’ in religious text books, and medicinal value of the beverage is well supported by modern science. Wine is a beverage well tagged with its geographical origin. This concept originally comes from French concept of terroir; which explains that a varietal wine from a defined region possess distinctive qualities. Wine makers of the past enjoyed this definition of quality for better marketing opportunities. Today, globalization and advancement in wine science created empowered consumers who could clearly discriminate quality of wines. In addition to a product with high sensory qualities, consumers expect a healthful beverage produced in an environmentally sustainable manner. Enology research projects focus on such aspects; and this chapter is a glance on enology advancements and proven health benefits of wine, such as cardiovascular health gut health, dental health etc.

P680: Reaction center chlorophyll in Photosystem II (PSII) which absorbs maximum light of 680 nm in its neutral state.

P700: Reaction center chlorophyll in Photosystem I (PSI) which absorbs maximum light of 700 nm in its neutral state.

P870: Form of bacteriochlorophyll in reaction center of pigment system in photosynthetic purple bacteria that absorbs light maximally at 870 nm in its neutral state.

Paclobutrazol: It is a chemical compound which inhibits Gibberellin biosynthesis. It is also a growth retardant commercially used in overcoming alternate bearing of mango.

Palindrome: Inverted repeats of DNA such that the sequence is the same when read forward or backward; e.g., CAGTTGAC, or in the English language, “Madam, I’m Adam.”

Palisade Parenchyma : Palisade parenchyma cells are seen beneath the upper epidermis. It consists of vertically elongated cylindrical cells in one or more layers. These cells are compactly arranged without intercellular spaces. Palisade parenchyma cells contain more chloroplasts than the spongy parenchyma cells. The function of palisade parenchyma is photosynthesis.

Pantothenic acid (Vitamin B₅): An important constituent of coenzyme A which is involved in transacylation reactions.

ABSTRACT

Green technologies are required in the field of food processing and production in order to achieve food security and to reduce adverse environmental impact. Application of nano technology in food processing and production can advance the food safety and quality, increase the bioavailability of nutrients and thereby improving human health. Nanotechnology can be applied to achieve green perspective like development of biodegradable packaging materials thereby reducing adverse environmental effect. Use of naturally occurring nanoparticles as additives can reduce the use of chemicals in food products. This chapter deals with the potential of nanotechnology to achieve green aspects in food processing and production.Main focusses are on achieving food security and environmental sustainability. Chapter also describes about the principles of nanotechnology and methods to achieve green aspectin food sector with the application of nanotechnology. Application of nanotechnology in food processing and production along with safety, regulations and accompanying laws are discussed in this chapter.

ABSTRACT

The commencement of the 21^st century has endorsed an extended requirement for safe and wholesome food. The fact is that consumer preferences, awareness and their concern towards food safety have been tremendously increased. Therefore, inactivation of pathogenic microorganisms through any treatment becomes essential for food processors to ensure that food is free from disease causing microorganisms and parallelly unaltered with respect to its organoleptic, functional and nourishing characteristic. Food industries predominantly adopt thermal inputs for the preservation of food. Thermal methods, however, lead to unfavourable changes in organoleptic and nutritional attributes, more particularly proteins and vitamins. Hence, there has been continuous development and advances in finding alternatives to conventional processing. Cold plasma technology is one such technique. Plasma can be defined as a quasi-neutral ionised gas and is more commonly termed as 4^th state of matter. Advances in plasma engineering have made it possible to generate plasma at atmospheric pressure which ultimately resulted in broadening the spectra of research on cold plasma at various interfaces of biological sciences. This chapter summarises the overview of cold plasma technology processing, numerous findings related to its application in the area of food decontamination, food fortification, seed germination, milk and milk products and modification of starches.

Keywords: cold plasma, non-thermal, plasma chemistry, fortification, modification, germination, plasma generation, novel

ABSTRACT

The rapid growth in population has created the need of industrialization and as a result there has been a significant increase in milk production and processing. Milk is a commodity which is consumed by persons of all age groups due to its nutritive value and health promoting attributes. However, the rapid growth in dairy sector has adversely affected the environment by emitting various greenhouse gases and thereby, resulting in global warming. Apart from it, there has been an increased usage of non- renewable resources like natural gas and coal in dairy sector. As a result, a viable balance has to be maintained between milk production and processing, environmental health and the rapidly growing population. This can only be achieved with the application of green or environment friendly technologies in all the stages of milk production and processing. This chapter will mainly deal with the various sources of greenhouse gases from dairy sector and on application of life cycle assessment and carbon foot printing for computing the impact of greenhouse gases on the environment. Also, this chapter will enclose various green technologies which can be applied in dairy sector to curb the greenhouse gas emissions.

Keywords: Carbon footprint, LCA, Greenhouse gases, Green Technology, Milk production, Milk Processing

Knowledge on fish reproductive biology is extremely important to understand various issues relating to reproduction and fishery management. Reproductive success in aquaculture systems depends to a greater extent on our knowledge about sexual differentiation, gonad structure, gametogenesis, spawning, larval metamorphosis, etc for successful captive breeding of a fish species. This chapter therefore, contains information on secondary sexual characters, sex-ratio, gonad structure, gonadal maturity, fecundity and embryonic development of striped murrel.

2.1 Secondary Sexual Characters

The sexes are separate in striped murrel however differentiation of sex is not easy when fish is immature. The differentiations in sexes become distinct with advancement of maturity during spawning season. On attaining full maturity, a good fecund mature female could be easily distinguished with having bulged belly originating nearing the site of pectoral fins and extends near to the vent.

Introduction

Conservation Agriculture (CA) is a set of soil management practices that minimize the disruption of the soil’s structure, composition and natural biodiversity. These include: i) maintenance of permanent or semi-permanent soil cover (using either a previous crop residue or specifically growing a cover crop for this purpose); ii) minimum soil disturbance through tillage (just enough to get the seed into the ground); iii) regular crop rotations to help combat the various biotic constraints. CA also uses or promotes where possible or needed various management practices listed below: i) utilization of green manures/ cover crops (GMCC’s) to produce the residue cover; ii) no burning of crop residues; iii) integrated disease and pest management; iv) controlled/limited human and mechanical traffic over agricultural soils. When these CA practices are used by farmers one of the major environmental benefits is reduction in fossil fuel use and greenhouse gas (GHG) emissions.

In India, efforts to develop, refine and disseminate conservation-based agricultural technologies have been underway for nearly two decades and made significant progress since then even though there are several constraints that affect adoption of CA. Particularly, tremendous efforts have been made on no-till in wheat under a rice-wheat rotation in the Indo-Gangetic plains. The technologies of CA provide opportunities to reduce the cost of production, save water and nutrients, increase yields, increase crop diversification, improve efficient use of resources, and benefit the environment. However, there are still constraints for promotion of CA technologies, such as lack of appropriate seeders especially for small and medium scale farmers, competition of crop residues between CA use and livestock feeding, burning of crop residues, availability of skilled and scientific manpower and overcoming the bias or mindset about tillage. The need to develop the policy frame and strategies is urgent to promote CA in the region. (Bhan and Behera, 2014).

Introduction

The resource conservation technologies (RCTs) primarily focus on resource-savings management systems for agricultural production through minimal tillage operation, maintaining soil health for available plant nutrients and conserving soil moisture through crop residues and/or cover crops, and following cropping sequence in spatial and temporal scale. The integration of resource-conserving technologies working in synergy is commonly referred to as conservation agriculture (CA). The CA is “a concept for resource-saving agricultural crop production that strives to achieve acceptable profits together with high and sustained production levels while concurrently conserving the environment” (FAO 2007). The CA envisages four principles: (i) minimizing mechanical soil disturbance and seeding directly into untilled soil, (ii) maximizing crop residue retention and/or growing cover crops, (iii) optimizing diversification of cropping sequences and rotations, and (iv) minimizing mechanical soil compaction through controlled traffic. The CA technologies involving no- or minimum-tillage with direct seeding and bed planting, residue management and crop diversification have potential for improving productivity and soil quality, mainly by soil organic matter build-up. Conservation agriculture systems appear to be appealing options to achieve sustainable and intensive crop production under different agroecological environments because they use available resources efficiently and maintain soil fertility. However, there is a need for wider scale testing of these new technologies under diverse production systems, as the CA technologies are site specific and therefore appraisal of CA is important to have significant adoption (Ramesh et al., 2016)

Introduction

There is a widespread degradation of natural resource, e.g., soil erosion, nutrient loss, water-logging, salinity, alkalinity, acidity, decline in soil organic carbon (SOC) content, ground water depletion and micronutrient depletion. The major causes are washing away of topsoil and organic matter due to water erosion, intensive deep tillage and inversion tillage, dismally low levels of fertilizer application, mining and other commercial activities, faulty agricultural practices, no or low use of organics, indiscriminate use of herbicides, pesticides, fungicides etc. Other cause is loss of organic matter with higher temperatures, which increase rate of microbial decomposition of organic matter due to adverse effect of climate change. Climate change due to global warming as a result of increased concentration of GHGs in the atmosphere is a well-established fact. Impacts of climate change are experienced throughout the world. Increases in global mean temperature, rise in sea-level, and occurrence of extreme events are the consequences of climate change. These changes may deplete the SOC pool and soil structural stability, increase soil’s susceptibility to water runoff and erosion, disrupt cycles of water, carbon, nitrogen, phosphorus, sulphur and other elements, and cause adverse impacts on biomass productivity, biodiversity and the environment. Climate change is likely to have a variety of impacts on soil quality. In order to restore soil quality, enhance productivity, it is of utmost importance to focus on conservation agriculture practices on long-term basis. Conservation Agriculture (CA) is gaining importance as an alternative to conventional agriculture.

Introduction

The main aim of conservation agriculture is to sustain and improve the crop productivity and to provide protection against biotic and abiotic stress, while at the same time protecting and enhancing the biological activities of the soil. The essential principles of conservation agriculture are no-tillage (and direct seeding) or reduced tillage, the maintenance of a cover of live or dead vegetative mulch on the soil surface and the wise use of crop rotations. The crop sequences are planned in such a way that which will discourage the buildup of pests or diseases and will help to optimize plant nutrient use by synergy between different crops of the rotation. While deciding the crop rotation, the locally important crops should be considered and there should be deep rooted and shallow rooted crops in the sequence so that the utilization of soil nutrients is maximized. At least one leguminous crop should be there in the crop sequence. The use of plant residues influences the soil physical, chemical and biological properties by reducing surface temperature, rate of evaporation and maintaining water content, nutrient load and rate of organic matter decay. The soils under conservation agriculture are happened to be highly active and diverse biologically and can supply plant nutrients for a longer period of time because of their higher nutrient loading capacities.

Soil biodiversity comprises of all organisms whether single-cell organisms or multi-cell animals or plants that live in the soil. Soil microbial diversity includes “genetic diversity, that is the amount and distribution of genetic information within microbial species, diversity of bacterial and fungal species in microbial communities, and ecological diversity, that is variation in community structure, complexity of interactions, number of trophic levels and number of guilds (Nannipieri et al., 2003).

Introduction

Intensive soil tillage, burning of crop residues and over use of fertilizer and irrigation water under current agricultural practices has accelerated the pace of degradation in Indian agriculture. Intensive soil tillage increases soil erosion and nutrient runoff into nearby waterways. Crop residue burning resulting in loss of plant nutrients and release of greenhouse gases (GHGs) in the atmosphere. Imbalanced use of chemical fertilizer leads to soil compaction, slows down the fertilizer utilization rate and contaminates the local environment. Increasing demand of irrigation water causes water shortage and harms the environment in several ways including increased salinity, nutrient pollution, and the degradation of flood plains and wetlands. In the face of these management and environmental challenges, there is a need to formulate such agricultural practices which improve the productivity of natural resources as well as of external inputs and help to prevent soil degradation. Conservation agriculture (CA) practices such as reduced tillage, residue retention and proper crop rotations offer such solutions. CA also helps in making agricultural systems more resilient to climate change and safeguard ecosystem services.

Introduction

Precise and continuous measurement the greenhouse gases (GHGs) fluxes/ emissions in agricultural systems are required for accounting and budgeting of carbon. Further, the long-term measurements of GHGs fluxes are equally important as precise measurement. Therefore, high frequency and long-term measurement of GHGs across the cropping systems are essential for chalking out the GHGs emissions mitigation strategies. Various technologies with definite working principles are used for estimation of GHGs emissions in agriculture.

Greenhouse Gases Estimation Techniques

Two basic principles are followed to estimate greenhouse gases in agriculture. One is the collection of GHGs from the field and subsequent analysis of the concentration of gases through gas chromatography (GC). Another principle is based on sensors measurement with the help of infrared gas analyze (IRGA). The two techniques used for the measurement are (i) ‘closed chamber method’ (manual/automatic), and (ii) ‘sensor-based method’. Generally, the GHGs fluxes in agricultural crop field are estimated by ‘closed chamber method’ for methane (CH₄) and nitrous oxide (N₂O). And for carbon dioxide (CO₂) measurement either soil respiratory chamber or canopy chamber is used that measures CO₂ with the help of infrared gas analyzer (IRGA).

6.1. Introduction

This chapter deals with the sample survey conducted on cotton, turmeric and castor seed farmers and recorded various benefits observed by them by using Futures market as a platform for price information. Further, it tries to examine the price discovery efficiency of commodity futures market with the help of secondary data.

It is often believed that future price is a forecast of the price of a commodity during the maturity month of its futures contracts. It is far from true. The futures price of a commodity traded at an exchange market is not so much determined by the anticipated supply of and demand for that commodity in the maturity month of its futures contracts as by the cost of carrying the commodity till the maturity of such contract. That means the spot and future prices of any commodity are always determined by the same basic forces of the present and prospective demand and supply. The difference between the two prices represents merely the cost of carrying the commodity from the present to the future. Such cost may be positive or negative depending on whether the current (not the future) supplies are abundant or scarce respectively when the price of futures contracts of any commodity is in reality relied upon by the physical market functionaries in that commodity as a “reference” price for executing their forward transactions in either the domestic or export market, that price may deem to be “discovered” in the true sense. The application of such reference price for transacting a forward transaction in the physical market in that commodity, in fact facilitates the use of the same future contract for managing price risk for such forward transaction. Hence, the price discovery and price risk management are the two sides of the same coin and efficiency of price discovery is directly related to the price risk management. A commodity exchange or a derivative market is not a mechanism for controlling prices. An efficient futures market is one that discovers prices and provides effective mechanism for managing price risk arising from unavoidable price variations owing to shifts in demand and supply schedule. Prices are determined by the basic demand and supply forces and not the market. Markets reflect the supply and demand conditions from time to time through variation in prices.

Rivolta (1873) first described the chain forming cocci in pus collected from the equine infection. Rosenbach (1884) established the genus Streptococcus’ Nocard and Mollereau (1887) first observed the relationship between the bovine mastitis and Streptococcus agalactiae. Lancefield (1933) classified beta-haemolytic streptococci on the basis of group specific-carbohydrate antigens.

Properties of genus

1. Morphology: Streptococci are gram positive cocci, capsulated, non-sporing and non-motile. Each coccus cell is 1µm in diameter. They are arranged in a pair or chain of cells as the cell division occurs in one plane(Figure 1 & 22). The chain formation and the chain length are variable. Streptococcus equi ssp. equi is a constant chain producer. Young cultures are gram positive whereas bacteria present in the pus and older cultures in the laboratory are often stained as gram negative.

Corynebacterium diptheriae was first observed by Klebs in 1883 and was described in details by Loeffler in 1884. So it is also known as ‘Klebs- Loeffler bacillus’. In 1888, Nocard isolated a similar type of bacteria from cases of bovine farcy. In 1894, Preisz described it completely and revealed its similarities with the diphtheria bacilli. Later it was named as Corynebacterium pseudotuberculosis (Preisz-Nocard bacillus). Bollinger (1890) first reported C. renale from the cases of pyelonephritis in cows.

The genus Trueperella was proposed by Yassin and others (2011) to describe T. pyogenes previously known as Arcanobacterium pyogenes or Actinomyces pyogenes or Corynebacterium pyogenes. The genus Arcanobacterium was first described (Collins and others, 1982) to include the bacteria originally isolated as Corynebacterium haemolyticum from the wounds of American soldiers. On the basis of 16S rRNA comparisons and menaquinone and phospholipid compositions it is proposed that the species Arcanobacterium pyogenes should be reclassified as members of the new genus Trueperella.

The genus Rhodococcus was first introduced by Zopf (1891) as a soil bacterium used in horticulture. Magnusson (1923) described C. equi (Rhodococcus equi) from suppurative pneumonia of a foal.

Antony Van Leeuwenhoek (1681) first observed the spirochetes under the microscope and described them. In 1833, Ehrenberg used the name Spirochaeta for free living spiral shaped organisms. Obermeir (1873) first described a spirochete of pathogenic significance isolated from human patients with relapsing fever. Inada (1916) first isolated Leptospira icterohaemorrhagiae from human patients of Weil’s disease. In 1980, Nogochi proposed the name as Leptospira.

In India, Taylor and Goyale (1931) first reported Leptospira from human patients suffering with jaundice in Andaman Islands. Ayyar (1932) first reported Leptospira from dogs in Chennai city.

In the previous chapter the physical methods of fruit and vegetables processing and preservation have been discussed. The present chapter deals with chemical method of fruit and vegetable preservation. In this method of preservation of fruits and vegetables, chemicals as preservatives are used to prevent the spoilage of fruit and vegetable products. These preservatives react with food (produce) constituents or microorganisms and create unfavourable conditions which hinder growth, activities and multiplication of microbes responsible for spoilage of food products. These chemical agents have maximum permissible limit of their use as law. They can be classified into two classes class I and class II.

Class I: Sugar, Salt and Oils

Class II: Sodium benzoate, Potassium metabisulphite (K M S) and Sorbic acid

Introduction and Concept

The word fungicide has originated from two Latin words: viz. fungus and caedo (to kill). So literally, a fungicide would be any physical or chemical agency which kills a fungus. However, the word is restricted to chemicals. Hence, the word fungicide should mean a chemical capable of killing fungi. However, there are a number of compounds which do not kill the fungus. They simply inhibit growth or spore germination temporarily. If the fungus is freed from such substances, it would revive. Such a chemical is called a fungistat. and the phenomenon as fungistasis. Some other chemicals, like certain phenantherene derivatives and bordeaux mixture may inhibit spore production without affecting vegetative growth. These are called antisporulants. There are other groups of chemicals which exhibit very poor or no antifungal activity in vitro condition but provide protection to the plants either by inhibiting the penetration of host surface by the fungi or by inducing the host defense system. The former type of chemicals are termed as antipenetrants and later as antipathic agents. Even though fungistats, antisporulants, antipenentrants, and antipathic agents do not kill fungi, they are included under the broad term fungicide because by common usage, the word fungicide has been defined as chemical substance which has ability to prevent damage caused by fungi to plants and their products. Fungicide which is effective only if applied prior to fungal infection is called protectants. On the other hand, fungicide which is capable of eradicating a fungus after it has caused infection, and thereby curing the plant, is called therapeutant.

INTRODUCTION

The World Wide has become one of the most important media for sharing information resources, digital documents, images, movies and various other types of resources. The research results, new findings, and opinions can also be put on the web from any where at any time. Owing to the dynamic nature of web information, the contents of many websites and their web pages are constantly being updated to reflect the latest changes.

The Web has also freed the user‘s dependence on library resources for finding information related to address and contact details of a person/institution, contents pages of books, journals, etc. Looking at the web has become an innovative trend in the reference service to complement dated print sources. At present many academic institutes in India have their own website and present all kinds of information about themselves. Information content is, however, one thing; Web site design and organisation is quite another matter. The existing institutions of Web sites are as different as are the institutions because even a high-quality institution may have a low-quality Web site that turns users off. Obviously, different institutions have a wide range of target groups, level of service, resources etc. Stover (1997) has outlined the different types of Web sites that academic, public and special libraries have created.

6.1 Introduction

The analysis of issues in agricultural credit in India reveals that the credit delivery to the agriculture sector continues to be inadequate. It appears that the banking system is still hesitant on various grounds to purvey credit to small and marginal farmers. The situation calls for concerted efforts to augment the flow of credit to agriculture, alongside exploring new innovations in product design and methods of delivery, through better use of technology and related processes. Facilitating credit through processors, input dealers, NGOs, etc., that are vertically integrated with the farmers, including through contract farming, for providing them critical inputs or processing their produce, could increase the credit flow to agriculture significantly.Agriculture plays a crucial role in the development of the Indian economy. It accounts for about 19 per cent of GDP and about two- thirds of the population is dependent on the sector. The importance of farm credit as a critical input to agriculture is reinforced by the unique role of Indian agriculture in the macroeconomic framework and its role in poverty alleviation. Recognising the importance of agriculture sector in India's development, the Government and the Reserve Bank of India (RBI) have played a vital role in creating a broad-based institutional framework for catering to the increasing credit requirements of the sector. Agricultural policies in India have been reviewed from time to time to maintain pace with the changing requirements of the agriculture sector, which forms an important segment of the priority sector lending of scheduled commercial banks (SCBs) and target of 18 per cent of net bank credit has been stipulated for the sector. The Approach Paper to the Eleventh Five Year Plan has set a target of 4 per cent for the agriculture sector within the overall GDP growth target of 9 per cent. In this context, the need for affordable, sufficient and timely supply of institutional credit to agriculture has assumed critical importance.

I. Definition of wasteland

Wasteland include degraded forest, overgrazed pastures, drought- struck pastures, eroded valley, hill slopes, water logged marshy lands, barren lands etc.

Different authors have defined wastelands as:

Land which is lying unproductive or which is not being utilized to its potential.

Land which is incapable of producing material or services of value (American Society of Soil science).

Land which has been abandoned and for which there is no further use (Mine spoils).

Land which produces less than 20% of economic potential. e) Land where no greenery can be sustained.

Land which is neither under forest cover or agricultural cover or assigned for specific purposes such as National park or National hydro power projects.

The Technical Task Group Report of the National Wasteland Board defines the wasteland due to different constraints.

In India rice is cultivated under two land situations. In uplands, rice is grown under rainfed conditions and the yield is normally low. In medium or low land conditions rice is grown under wet condition where plenty of rain water or irrigation water is available. Here an intensive tillage is practiced in wet to create a soft puddle condition and then paddy is transplanted. Land submergence is thus an essential condition for successful rice cultivation.

Rice soils are not necessarily soils with water at or near the surface. Many soils have a fairly deep water table, but their surface is kept under submergence maintaining depth of 3-5 cm water. This condition is maintained either by puddling when wet or by having a compacted layer in the sub surface.

A rice soil is characterized by reducing conditions, when it is cropped with rice during wet season and oxidizing conditions during dry season, when the land remained fallow or planted with dry season crops if, irrigation water is available.

1. INTRODUCTION

India produces a large variety of fruits and vegetable due to varied agro-climatic conditions. These include mango, citrus, banana, apple grapes, strawberry, pineapple, litchi, guava, papaya, plum, peach, pear apricot etc. Astonishingly, it may appear but it is a fact that postharvest losses of fruits and vegetables in India are staggering. Infact the postharvest losses of fruits and vegetables are equivalent to the annual consumption of fruits and vegetables in U.K. In this article, a focus is made on the causes of postharvest losses of fruits, overview of various techniques used to prevent the postharvest losses constrains in postharvest technology and future strategies.

1. INTRODUCTION

Every fruit or vegetable is harvested keeping in view, its intended use. At what stage it should be harvested, is indicated by the maturity index. The chapter focuses on these and postharvest quality of fruits and vegetables.

2. FRUIT MATURITY

"Maturity of a fruit can be defined as that stage at which a commodity has reached a sufficient stage of development that after harvesting and postharvest handling, its quality will be at least the minimum acceptable to the ultimate consumer”. Maturity is of two types:

1. INTRODUCTION

Indians are known to prepare preserves from the ancient times. They were also familiar with ther therapeutic values associated with the preserves. Besides, candies, reathers and toffees are the other food products prepared and consumed. In this chapter, the methods of their preparation are described.

2. PRESERVES

A preserve is made from properly mature fruit, by cooking it whole or in the form of large pieces in heavy sugar syrup, till it becomes tender and transparent. In its preparation not less than 45Kg of the fruit are used for every 55Kg of sugar, and cooking is continued till a concentration of at least 68 per cent of TSS (Total Soluble Solids) is reached.

Freshly made preserves are wholesome and have an attractive appearance. When they are stored for a long period, their natural colour and flavour deteriorates on account of oxidative changes. They should therefore, be made only during the season, unless there should be adequate facilities to keep the fruits so that they are available in the off-season also.

1. INTRODUCTION

Fermentation is an age old technology. It has been used by man since antiquity. It has been employed to produce a number of fermented products such as wine, beer, curd, vinegar, pickles and several others. Fermentation was discovered quite early and by chance but the underlying principles were discovered very late. Primarly fermentation was used as a method of shelf-life extension of the produce in the time of glut production, though the final product had modified sensory qualities. Thus, fermentation and drying were the main methods of preservation. With the discovery of new methods of preservation, fermentation as a method of preservation has gone into background and as technique of flavour development and product with modified sensory quality came into practice. In this chapter, fermentation as a method of preservation has been described.

4.1 Introduction

Many styles of gardens do not follow strict rules and so those are known as informal gardens. Some gardens evolved as informal garden in due course of time as per the choice of people but some gardens are informal in nature from origin. Informal gardens are:

English garden

Japanese garden

Hindu garden

Buddhist garden

12.1 Introduction-Nitrogen

Nitrogen is a chemical element which has the symbol N and atomic number 7. Elemental nitrogen is a colourless, odourless, tasteless and mostly inert diatomic gas at standard conditions, constituting 78.1% by volume of Earth’s atmosphere. Nitrogen is a constituent element of all living tissues and amino acids. Many industrial important compounds, such as ammonia, nitric acid, and cyanides are made up of nitrogen.

12.1.1 History

Nitrogen (Latin nitrogenium, where nitrum (from Greek nitron) means “native soda”and genes means “forming”) is formally considered to have been discovered by Daniel Rutherford in 1772, who called it noxious air or fixed air. That there is a fraction of air that did not support combustion is well known to the late 18th century.

Argon was discovered when it is noticed that nitrogen from air is not identical to nitrogen from chemical reactions. Compounds of nitrogen were known in the Middle Ages. The alchemists knew nitric acid as aqua fortis (strong water). The mixture of nitric and hydrochloric acids is known as aqua regia (royal water), celebrated for its ability to dissolve gold (the king of metals). The earliest industrial and agricultural applications of nitrogen compounds involved uses in the form of saltpeter (sodium- or potassium nitrate), notably in gunpowder, and much later, as fertilizer, and later still, as a chemical feedstock.

5.1 Introduction

The development of quantitative trait loci (QTL) mapping methods to identify genes or QTLs controlling quantitative traits was a landmark achievement in plant genetics research in the late 1980s. Since then literally thousands of research papers have reported the identification of genes or QTLs for important traits across a diverse range of plant species. This wealth of genetic information was built on the foundation of decades of research in crop molecular genetics and genomics.

The selection and enrichment of QTLs within breeding material was the inevitable next step from QTL discovery to application, and there have been numerous reports of successful tracking of genes and QTLs within breeding programmes. DNA (or molecular) markers have enabled selection of major genes or QTLs for critical or important traits in a process called marker-assisted selection (MAS), which has revolutionized plant breeding. DNA markers are used as tools by breeders to improve the accuracy or efficiency of selection as well cost and time efficiency. Apart from MAS, DNA markers have numerous applications including DNA fingerprinting, genetic diversity analysis and parental characterization.

Recent developments in genotyping platforms and systems to implement molecular breeding schemes offer new tools for modern plant breeders. Single nucleotide polymorphism (SNP) markers are biallelic, co-dominant markers which are abundant in the genome. Insertion-deletion (Indel) markers are also prevalent and can be screened using high-throughput genotyping platforms. These platforms are cost-efficient, can handle large sample sizes and provide fast data turn-around time. The availability of genome sequences and genomic resources continues to provide a wealth of SNP and Indel markers which will undoubtedly be the marker type of choice for decades to come.

The availability of high-throughput SNP platforms in conjunction with advances in computational methods has also led to the molecular dissection of traits using genome-wide association studies (GWASs) across diversity panels and the development of genomics-based molecular breeding strategies. Association mapping (AM) has now emerged as a standard method for gene and QTL discovery for major crops.

1. Context

Women play a critical role in agriculture, and agriculture continues to remain the major livelihood strategy for women as well as millions of small, marginal and poor farming households in India. Despite this, farm women lack access to extension services as extension programmes rarely identify women as an integral client. Farm women and men have differential needs for knowledge, information, technology and skills as often they are involved in different activities spread over time and cropping seasons. Besides these, men and women farmers have differential access to assets, information, markets, credits, and other services that are necessary for using new knowledge, technologies and skills. Ignoring women while delivering services and technologies creates a gap as many of the agricultural operations are performed by women only.

It is estimated that if women had the same access to productive resources as men, they could increase yields on their farms by 20-30 per cent (FAO, 2011). Yields on plots managed by women are lower than those managed by men, as they do not have the same access to inputs. If they did, their yields would go up, they would produce more, and overall agricultural production would increase. It isn’t merely about enhancing productivity but also about being fair and equitable. Women are a significant part of the agricultural workforce and they deserve to be consulted prior to formulation of agricultural development plans and policies. SDG 5 on Gender Equality “Achieve gender equality and empower all women and girls” is closely aligned to this aspect. Moreover, enhanced access to services can help women grow more food, have more say in the family, and could potentially lead to more income and food in women’s hands-leading to better food security and nutrition for the entire family as they are the major caregivers in the family.

1. Background

Agriculture sustains 58 per cent of population in India. Productivity and profitability are two major planks for food security and sustainable livelihood of farmers. About 86 per cent of farmers in India own less than two hectors of land. As a result, their marketable surplus is small which poses a major challenge in ensuring remunerative price. Limitations associated with quality of produce, storage, transportation, credit as well as vagaries of weather and market are other related problems. These limitations further aggravate if the producers happen to be women due to their socio-cultural and economic position in the society. Only a decentralised and income assuring approach alone can bring prosperity to the farmers apart from gender equality. This would ultimately propel the agricultural growth of the country.

The chapter discusses one of such approaches called the public private partnership (PPP). It has gained prominence in the wake of the demand for farm reforms, trade, commerce, climate change and gender equality in recent years.

1. Introduction

Fisheries is an important sector of food production which besides providing nutritious food to millions also serve as a livelihood option for many. It helps to bring about people centered rural development that protects the environment. Conventionally, fishing has been considered a male domain, because of the assumption that social, cultural, or religious taboos prevent women from participating in fishing activities. In fact, the involvement of women in fishing and related activities has remained invisible and unrecognized till the late 1980s. However, the publications and policy reports during the period highlighted the valued contributions by women in fisheries sector to economies and food security around the world (Harper et al., 2020). Several high-level fisheries reports and policy instruments that followed added to this momentum and emphasized the importance of principles of gender equality in ensuring sustainable coastal livelihood security. Present day estimates indicate that there are around 60 million people who are directly engaged in the primary sector of fisheries and aquaculture globallyof which 14 per cent are women (FAO, 2018) Asia tops the list with the highest number of fishers and aquaculture workers (85 per cent of the world total), followed by Africa (9 per cent), America (4 per cent) and Europe and Oceania (1 per cent each) (FAO, 2018). However, despite growing attention to women and gender in fisheries there exits glaring gap in the gender disaggregated data from fisheries sector that is skewed against women worldwide. These warrant the need for the implementation gender balanced fisheries policies and management strategies that support women empowerment in the sector.

1. Introduction

Economic growth and the commercialization of agricultural systems have enhanced the adoption of various technological interventions in the farming systems (Rola-rubzen et al., 2020). The green revolution is one of the successful examples of technology interventions, which led to the agriculture transformation and thereby brought reduction in the hunger and poverty of India (Minten and Barrett, 2008). It conclusively proved that the adoption of these farm technology interventions can increase production, productivity and farm income. The technology interventions consisted of a package of improved crop varieties, irrigation, fertilizers, plant protection chemicals, and agricultural machinery.It also brought to fore that the nation’s capacity to maximise its agricultural production potential also relied upon the responsiveness of farmers who were the ultimate decision makers. Thus the availability and accessibility of these technologies to the farmers, and their ability to adopt and utilise these technologies assumed paramount significance in the whole process.

Later decades of twentieth century proved that, along with men, women’s role is vital in agricultural production and they are the backbone of the rural economy in many developing countries including India. It is reported that women are responsible for more than 50 per cent of the world’s food production and account for about 43 per cent of the total agricultural labour force (Doss, 2018). In India, about 78 per cent of economically active women are engaged in agriculture compared to 63 per cent of men. Moreover,in rural India, almost 50 per cent of rural women are classified as agricultural labourers and 37 per cent as cultivators.

Plant breeding is the art and science of changing and improving the heredity of plants. The art of plant breeding lies in the breeder’s skill in observing and selection of superior plants. The value of selection largely depends upon the skill of the breeder. The skill that a breeder develops though a close and deep study of the concerned crop species. Before the rediscovery of the Mendelian Laws in 1900 AD, the plant breeding is as an art. The modern age of plant breeding began in the early part of the twentieth century, after Mendel’s work was rediscovered. Today plant breeding is a specialized technology based on genetics. It is now clearly understood that within a given environment, crop improvement has to be achieved through superior heredity. Plant breeding developed into a science as knowledge progressed towards the genetics, cytogenetic, physiology, pathology, biochemistry, biotechnology and biometry. The fundamental of plant breeding was based on recognition of the genes. The genes were identified by their effects on the visible expression of plant traits such as whether a plant was a dwarf or tall, or the flower color was white or pink. Through systematic hybridization, a desirable gene could be transferred from one to another cultivar. More recently the science of molecular genetics proposes to advance plant breeding. Molecular genetics was ushered in with the description of chemical structure of deoxy-ribonucleic acid (DNA), the material that constitutes the genes. DNA carries the instructions for synthesis of specific proteins that determine the visible expression of particular characters. The new technology does not supplant nor diminish the importance or need for traditional selection and crossing procedures in the breeding of improved cultivars. The performance of today’s cultivars reached at high levels through refined selection and hybridization breeding procedure.

The early developments in plant breeding that took place are based on archaeological evidence. The first efforts to grow wild plants probably occurred in Southeast Asia culminated in the domestication of some of the many plants with which humans experimented in 13000 BC. By 10000 BC, advanced knowledge existed of such plants as rice (Oryza sativa), several legumes such as pea (Pisum sativum), runner bean or broad bean (Phaseolus or Vicia spp.) and possibly soybean (Glycine max). At this point crops became domesticated.

Although the beginning of civilization in China and Southeast Asia are obscure and fragmented. The number of successful species domesticated indicates considerable success in plant breeding. The third site of independent agricultural development and plant breeding was in south-central Mexico between 6700 and 5000 BC. Squash and avocados were domesticated first and a number of species of maize. Domestication in the Middle East and China included the self-fertilized crop like cereals and soybean.

Plant Propagation

Plant propagation involves the formation and development of new individuals, which are used in establishment of new plantings. It is simply the reproduction or multiplication of a plant from a source that is often referred to as a mother plant. In general, two methods are employed: 1) sexual and 2) asexual. Sexual propagation is multiplication of plants from seed and asexual or vegetative propagation involves starting a new plant from some vegetative part of a plant. Propagation by seed results in seedling variability. It is an extreme disadvantage for a nursery operator trying to produce a uniform crop containing chosen desirable characteristics. Seed propagation is not practiced in fruit nursery as plants raised by this method fail to bear true to type fruits.

Germination of seed

The activation of the metabolic machinery of the embryo leading to the emergence of a new seeding plant is known as germination. Germination is essentially a quickening of the growth of the embryo. As germination proceeds, the growing points of the radical and plumule divide rather rapidly Usually the radical emerges from the seed coat first, proceeds downward, and develops into the root system, the plumule proceeds upward and develops into the shoot system. Germination is entirely a food utilization process. Processes going on in seed during germination are: 1) Absorption of water; 2) Secretion of enzymes and hormones; 3) Hydrolysis of stored food into soluble form; and 4) Translocation of soluble foods and hormones to the growing points. These processes are either wholly or in part influenced by the food reserves, hormone supply, water supply, oxygen supply and temperature level.