eChapters

Growth is defined as an irreversible change in the size of a cell, organ or whole organism. Commonly, growth is the increase in the amount of living material (protoplasm) which leads to an increase in cell size and ultimately cell division. Growth occurs only in living cells by metabolic process involved in the synthesis of proteins, nucleic acids, lipids and CHO at the expense of metabolic energy provided by photosynthesis and respiration.

Crop nutrition / plant nutrition refers to the inter relationships of mineral elements in the soil and their role in plant growth and development. This inter relationship involves a complex balance of mineral elements essential and beneficial for optimum plant growth.

Plants require certain element for their growth and development. There are about 60 chemical elements present in the plant and it doesn’t mean that all are essential for normal growth and development.

Arnon and Stout (1939) proposed criterion of essentiality. Which were refined by Arnon (1954) and are popularly known as Arnon’s criteria of essentiality. They are:

Crop density is nothing but number of plants or seedling per unit area. Crop density per unit area depends on the soil, climate and type of crop being planted. For example under extreme conditions, in poor soils and in semiarid regions with no irrigation planting at low density is best. Otherwise crop plants will be thin and weak. In such conditions not only produces low yield but also is the ideal condition for pest and diseases. Crop unit area depends on :

1. Soil fertility: In poor soils, plant density should be lower than in fertile soils.
2. Availability of water: In areas where water is a limiting factor, planting should be done at a lower density.
3. Tillering capacity of the crop: Small grains and other cereals are planted at lower densities due to tillering capacity and elasticity of the crops.

Cultivation involves management of physical environment to produce a favourable habitat for successful crop production. Primitive man used tools to disturb the soil for placing the seeds. The word tillage is derived from the Anglo-Saxon words tilian and teolian means to plough and prepare soil for seed sowing, to cultivate and to raise crops. Jethrotull who is considered as father of tillage suggested that ploughing is necessary so as to make the soil into fine particles.

Tillage is the mechanical manipulation of the soil either with tools and implements for obtaining conditions ideal for seed germination, seedling establishment and growth of crops.

Tillage includes all operations and practices that are used for the purpose of modifying soil physical characters. Tillage is the most difficult and time consuming operation in crop production. About 30 per cent of the total cost of cultivation goes for tillage operations.

Soil is defined as a thin layer of earth’s crust which serves as a natural basic medium for the plant growth. Soil is a dynamic natural body composed of minerals, organic materials and living forms on which plants grow. Soil are formed by the weathering of rocks and minerals in presence of soil forming factors like climate, organisms, relief or topography, parent material and time (cl,o,r,p,t).The weathering of rocks and minerals are associated with physical and chemical phenomenon. The principal agents of physical weathering are temperature, water, wind, plant and animals. Chemical weathering is affected through the process of hydrolysis, hydration, carbonation, oxidation and reduction.

Each soil is characterized by a given sequence of horizons. Combining of this sequence is known as soil profile. Soil profile is a vertical section of the soil through its horizons. The layers or horizons in the soil profile vary in thickness and have different characteristics like colour, texture, structure etc. The horizons are designated by O, A, E, B, C and R.

Horizon: The layers seen in the vertical section of the soil profile are called horizons.

Seed is the living link between plant and progeny and biologically seed is ripe fertilized ovule and a unit of reproduction of flowering plant. Agronomically, a seed material or propagule is the living organ of crop in rudimentary form used for propogation.

Propagation Asexual Sexual Seed Stem cutting Ex: Sugarcane Grafting Rooted slips Ex: Grasses Tubers Ex: Potato Budding Corms Rhizomes Layering

Plants perpetuate / multiply either sexually or asexually. Sexual methods are through seeds and asexually through vegetative parts. Most of the crop plants produce viable seeds which are used for sowing. Those used for multiplication are called seeds and those which used for human consumption are called grains.

Seed consisting of intact embryo, stored food and seed coat which is viable and has got a capacity to germinate. Embryo has two parts:

Crops: Is a cultivated plant that is grown on large scale commercially, especially cereal, pulses, fruits or vegetables.

Classification of crops : Several crop plants are alike with respect to ontogeny (Development), morphology, anatomy, physiology and requirement of environment. Classification is done to generalize similar crop plants as a class for attaining better understanding of them. Field crops are classified in several ways.

Agriculture plays a key role in the overall economic and social well being of the country. Though the share of Agriculture in both GDP and employment has declined overtime, Agriculture still forms the backbone and occupies a pride of place :

1. Agriculture contributes 24 per cent to the Gross Domestic Product. GDP was declined from 39 per cent in 1983 to 25 per cent during 1999-2000 and now it 17.32 per cent.
2. Provides livelihood support for more than half of the population in the country. The sector provides employment to 56.7 per cent of the India’s work force.
3. Agriculture has been the source of raw material for industries. Majority of the industries depending on agriculture for their raw materials. Ex: Textile (Cotton, Jute), Sugar (Sugarcane, Sugar beet), Small & medium scale industries like soaps, dyes, medicines, vitamins, preservation of fruits and vegetables, dhal milling, rice husking, Jaggery making, oil crushing, handlooms etc.
4. It provides large part of market for industrial goods viz., seeds, fertilizers, pesticides, implements, machines like pump sets, trucks, tractors, power tillers, sprayers etc.
5. Support roadways, railways, airways and shipways for transport of inputs & produce.

Higher plants demand certain basic things for their growth. As many as 52 factors (basic things) influencing crop growth have been identified :

• 100 per cent of the land has sufficient CO₂ in the atmosphere and sunlight
• 83 per cent have favourable temperature
• 64 per cent have favourable topography
• 46 per cent have reliable rainfall
• 40 per cent have satisfactory fertile land

It is supposed that man was evolved on earth about 15 lakh years ago. This man started to move by standing erect on his feet and called Homo erectus L. Later the modern man was evolved called Homo sapiens L. (Sapiens means learning habit) due to his continuous learning habit. It is difficult to trace the exact period of beginning of agriculture. Archeological evidences indicated that, Agriculture started about 50,000 years ago.

Hunting was the primary source of food in olden days and was prevailed for long time. They obtained his food through domestication of some animals like dogs, horse, cow, buffalo etc. They live in the periphery of the forest and migrate from one place to another in search of food. It was not comfortable and they started enjoying by settling at one place near the river and started agricultural system.

Agronomy is a branch of applied science deals with the principles and practices of field crops production and management of soil for higher productivity. The term Agronomy is derived from Greek word agros meaning field and nomos meaning to manage.

Norman (1980) defined Agronomy as the science of manipulating the crop environmental complex with dual aims of improving Agricultural productivity and gaining a degree of understanding of the process involved.

In recent times, Agronomy has assumed newer dimensions and can be defined as ‘A branch of Agricultural science that deals with the methods which provide favourable environment to the crops for higher productivity’.

Agriculture

The term agriculture is derived from Latin word ager or agri meaning soil and cultura meaning cultivation. Agriculture is a broad term encompassing all aspects of crop production, livestock farming, fisheries, forestry etc. Agriculture is a branch of applied science and is the art of farming including the of cultivating the soil for producing crops and raising livestock. There are three main spheres of agriculture-geoponic meaning cultivation in soil, hydroponic meaning cultivation in water and aeroponic meaning cultivation in air.

Agriculture is a productive unit where the gifts of nature like land, light, water and temperature are integrated into a single primary unit that is crop plant which is indispensable for human beings. The secondary productive units of agriculture are animals including livestock, birds and insects which feed on the primary units and provide concentrated products such as meat, milk, wool, eggs, honey, silk and lac.

An experiment is a systematic process or activity which leads to collection of information on certain objects to give an answer to the objectives of the researcher.

The experiment in which certain absolute values like average, correlation coefficient, median, mode, etc are worked out to describe the population is known as absolute experiment.

The experiment in which the effects of different objects under consideration are compared is known as comparative experiment.

The variable whose change we wish to study is called as Response variable. For example- yield, mortality rate of insects etc.

The variable whose effect on the response variable we wish to study is termed as Factor. For example - variety, fertilizer, insecticide etc.

Here factor is the independent variable and response variable is the dependent variable.

The various levels of a factor whose effect on the response variable we wish to study are known as Treatment.

Chi-square test is a non-parametric test as the null hypothesis does not contain any assumption regarding the population parameter. Chi-square is also written as c₂. In this chapter two uses of chi-square test will be dealt with. They are the following :

Samples having size, n - 30 are known as large sample. For large values of n (i.e., for n - 30), almost all the distributions are very closely approximated by normal distribution. Thus in this case we apply the normal test, which is based upon the area property of the normal probability curve. Large Sample Test is also known as Z-test or SND (Standard Normal Deviate) test.

A sample is said to be small sample if the sample size(n) is less than 30. Various small sample tests are: (i) t-test (ii) F-test

t-test performs the following tests for small sample(s).

1. To test the equality between a single sample mean and the assumed population mean.
2. To test the equality of two independent sample means.
3. To test the equality of two paired sample means.
4. To test the equality between sample correlation coefficient and the assumed population correlation coefficient

The aggregate of data forming a subject of investigation is known as population. Example, All the crop plants grown in a plot; all the fruit plants in an orchard, etc. The population may be:

1. Finite: No. of observations are definite. e.g., number of farms in a village, no. of house in a locality, no. of trees in an orchard are all finite population.
2. Infinite: Number of observation are indefinite e.g., (a) Number of insects in a region, number of grasses in a field etc. are all infinite population.

The Population may be:

1. hypothetical or theoretical

   Hypothetical population consists of unit that has no physical existence. This population exists only in imagination. For example, Result of tossing coin, throwing die,

2. Existent or real population consists of units that are physically present. This population actually exists. For example, Number of employees in a factory, Number of farms in a village.

Concept of correlation was given by Karl Pearson in 1890.

The study of strength and nature of relationship between two variables is called correlation. Two variables are said to be correlated, if the change in one variable affects the other variable. Correlation is also known as covariation.

Bivariate Distribution: Distribution involving two variables is known as bivariate distribution. For example, Height and weight of persons, yield and production of a crop in.

On basis of type of association between variables, correlation is of two types:

Random variable: A random variable is a variable that assumes numerical values associated with the events of a random experiment whose outcomes cannot be predicted with certainty. For example, Height of rice plants in a field; seed weight; No. of tillers per rice plant.

A random variable is of two types:-

1. Discrete random variable: The random variable which takes only countable values i.e., integral values. For Example, Number of tillers per rice plant. Here there can be finite no. of values between any two values.
2. Continuous random variables: The random variable which takes values within intervals. These values cannot be counted but can only be measured. Here there can be infinite no. of values between any two values for example, Height of rice plants in field; seed weight.

In some experiments the result can be predicted with certainty. For example, the bulb will stop glowing when switched off, the evolution of hydrogen gas when zinc reacts with dilute hydrochloric acid. Such phenomenon where the result can be predicted with certainty is known as deterministic phenomenon. But in some experiments the result cannot be predicted with certainty. For example, Sales of a firm, profit made by a company, yield of a crop, etc. Such phenomenon where the result cannot be predicted with certainty are known as probabilistic or random phenomenon. Such phenomena are frequently observed in economics, business, agriculture, social science, biology, etc., and in our day to day life.

The theory of probability is a very important branch of statistics which provides a numerical measure of uncertainty.

Literal meaning of dispersion is scatterdness. We study dispersion to have an idea about the homogeneity and heterogeneity of the distribution. Dispersion gives an idea about how much the values of the observation varies from their averages. The series in which the values of the observation differ much from their averages is said to be heterogeneous or highly dispersed. The series in which the value of the observation does not differ much from their averages is said to be homogenous or less dispersed.

There are two types of measures of dispersion:

Measures of central tendency are also known as averages. Averages are defined as statistical constants which enable us to understand in a single effort, the significance of the whole i.e., they are the representative value of the distribution. They give an idea about the concentration of the values in the central part of the distribution.

Five Types of Averages

Arithmetic Mean

It is the sum of all the observations divided by the number of observation.

For individual data or simple series (i.e., series in which all values have single frequency)

Presentation of data is done in form of diagram and graphs.

Diagrammatic Presentation: The data are presented in form of diagrams

The important diagrammatic presentations are simple bar diagram, multiple bar diagram, component bar diagram, percentage bar diagram & pie diagram.

Selection of diagram depends upon the nature of classification, number of characters involved and the type of comparison required to be made. In all the diagrams, the groups or classes are represented on the X-axis and the volumes or frequencies are represented in the Y-axis. The title of these visual aids should be self-explanatory.

1. Simple Bar Diagram: Simple bar diagrams consist of vertical bars of equal width. The height of these bars is proportional to the magnitude of the attribute. All bars are separated from each other by equal intervals. Simple bar diagram is used if the classification is based on attributes and if the attributes are to be compared with respect to a single character. For example, the area under different crops in a state, the production of mangoes in different years for a state, the yield of a variety at different fertilizer level, etc, can be represented by the simple bar diagram. Also the yield performance of different varieties of a crop, the effects of different treatments etc, can be compared using simple bar diagrams.

Frequency distribution table is a statistical table which shows the sets of all distinct values of the variables arranged in order of their magnitude either individually or in groups with their corresponding frequencies side by side.

Need for frequency distribution table

1. To condense the data
2. To provides quick reference for the entire data
3. To facilitate quick & easy statistical analysis of data
4. To reveal the pattern within the data

The word ‘statistics’ has been derived from the Latin Word ‘Status’ which means ‘Political State’. The word statistics has been coined by Gottfried Aschenwall, a German Political Scientist. Ronald Aylmer Fisher is regarded as father of modern statistics. The word statistics has meaning both in plural and singular sense. In plural sense, it means quantitative/qualitative figures. For example, the area under food grains in different states of India, the production of guava in different states of India, germination percentage of seeds, etc.. In singular sense, it means as a subject i.e., method of dealing with the quantitative/qualitative information.

Statistics is defined as scientific method which deals with collection, organization presentation, analysis and interpretation of data. It is included under both science and arts. Statistics is used as a tool to obtain knowledge on other subjects of science.

Abstract

The use of plants for treating diseases is as old as the human species. Popular observations on theuseandefficacyof medicinal plants significantly contribute to the disclosure of their therapeutic properties, so that they are frequently prescribed, even if their chemical constituents are not always completely known. Medicinal plants have therapeutic potential due to the presence of natural antioxidants functioning as reducing agents, free radical scavengers and quenchers of singlet oxygen. Majority of their antioxidant activity is due to bioactive compounds viz. flavones, isoflavones, flavonoids, anthocyanins, coumarins, lignans, catechins and isocatechins. They have been recognized to possess several medicinal properties (diuretic, expectorant, laxative, anti- bacterial, anti-pyretic etc.) and have been effectively used in the indigenous systems of medicine in India and other countries. Apart from the traditional use, a number of beneficial physiological effects have been identified by extensive studies. Among these are their beneficial effects on lipid metabolism, efficiency as antidiabetics, ability to stimulate digestion and to inhibit platelet aggregation, antioxidant, antilithogenic and anti-inflammatory potential.In this chapter an attempt has made to elucidate and understand the chemical and medicinal properties of Stavar and Safed musli those are using as medicine. These may also use as ingredients for preparation of herbal food products.

Abstract

Fats and oils are one of the five essential ingredients of human diet and the others are protein, carbohydrates, minerals and vitamins. The oil seeds are major source of edible in world. Oils and fat form an important constituent of human food. Lipid metabolism generates many bioactive lipid molecules, which are fundamental mediators of multiple signaling pathways and they are also indispensable compounds of cell membranes. Many people in developing countries, especially children under five years of age suffer from acute or chronic protein and energy shortages. There is definitely a need for food production to keep pace with the increase in the number of the world’s population. Oilseed and nut should be properly dried before storage, and cleaned to remove sand, dust, leaves and other contaminants. All raw materials should be sorted to remove stones and moudly nuts. Some moulds, especially in the case of groundnuts, can cause aflatoxin poisoning.

Introduction

Oil has been a vital part of people’s regular dietary consumption all over the world and its usage has been found to increase several folds over the decades. The importance of using the appropriate oil for cooking goes a long way in affecting the consumer’s health. Improper methods of oil-aided cooking can lead to cardiovascular diseases and increased cholesterol in the blood (Kumar et al., 2018). There is definitely a need for food production to keep pace with the increase in the number of the world’s population. In order to achieve these national development strategies in many based economy tropical countries on agriculture and biased now towards increasing diversity of food products and consumer in order to alleviate malnutrition and pressure to strengthen and expand based industries on agriculture to ensure that their products are both healthy and safe. Oils and fats for food have used a variety of other applications since prehistoric times, and were easily isolate the source of the fats and oils found useful because of its unique properties.

Abstract

Herbal Burfi was development with various types of milk viz., Buffalo (6% Fat), Cow (4% Fat) and mixed milk (5% Fat) and different levels of sugar i.e. 20, 25, 30 and 35 per cent (weight basis of khoa). Each sample was fortified with 5g satavar and safed musli powder. Other minor ingredients like Almonds, Cardamoms, Cashew nuts, Pistachio nuts, etc were mixed thoroughly and after preparation herbal burfi was allowed to set at room temperature (20- 25_oC) for two hours. Physico-chemical (acidity, pH, fat, protein, lactose, sugar, ash and total solids), microbial (total plate count, coliform count, yeast and mould count) quality and sensory attributes of the herbal burfi were evaluated. The data of experiments were statistically analyzed to compare significance effects of various factors by applying factorial Randomized Block Design (fRBD) with the help of OPSTAT software and ANOVA.

Abstract

Food texture is one of the most widely measured quality attributes during postharvest handling, processing, and consumption. Given the subjectivity in human perception of food texture, texture measurement remains a complex exercise and thus presents both a charm and challenge for researchers and industry practitioners. For fresh foods such as fruit and vegetable, textural properties such as firmness are widely used as indices of readiness to harvest (maturity) to meet requirements for long term handling, storage and acceptability by the consumer. For processed foods, understanding texture properties is important for the control of processing operations suchasheating, frying and drying to attain desired quality attributes of the end product. Texture and viscosity measurement is one of the most common techniques and procedures in food and postharvest research and industrial practice. Foods are complex systems exhibiting various degrees of elasticity, viscosity, and plasticity. Because of its complex structure and mechanical behavior, objective measurements of food texture may be influenced by a variety of test conditions, including rate of loading, the magnitude of deformations imposed upon the material, geometry of the loading surface, and localized yielding within the product tested. Various approaches have been used to evaluate the sensory attributes of texture in foods. However, the high cost and time consumption of organizing panelists and preparing food limit their use, and often, sensory texture evaluation is applied in combination with instrumental measurement.

Humankind has always been a perceptive feel for rheological testing, e.g. in physical and visual evaluations of material properties such as hardness, stiffness, flexibility, and viscosity, and their relation to end-use quality characteristics. People often naturally measure the quality of solid foods by gently squeezing them, or liquid viscosity is measured by gently rotating the liquid in its container. These intuitive measurements gradually became formalized into quantitative descriptions of material properties.

Rheology can be defined as the study of how materials deform, flow or fail when force is applied. The name is derivated from Greek word: rheos, meaning the river, flowing, streaming. Therefore rheology means “flow science”. Rheological investigations not only include flow behaviour of liquids, but also deformation behaviour of solids. Normally, to measure rheological properties, the material is subjected to a controlled, précised and quantifiable distortion or strain over a given time and the material parameters such as stiffness, modulus, viscosity, hardness, strength or toughness are determined by considering the subsequent forces or stresses (Dobraszczyk and Morgenstern, 2003). The term rheology was coined by Eugene C. Bingham, a professor at Lafayette College, in 1920, from a suggestion by a colleague, Markus Reiner (Steffe, 1996)

Abstract

Physical properties of food are aspects such as colour, structure, texture, rheology and interfacial properties, and composition. We have a range of instrumental methods for objectively characterising and measuring food structure and physical properties. These are useful for applications such as new product development, benchmarking, reformulation and specification.

Colour

Consistent and accurate measurements of the colour and visual appearance of food products is extremely important. Various methods are available for colour measurement, allowing a wide variety of sample types to be measured. Colour measurement results are typically provided on the CIELAB scale. Others are available on request.

Abstract

In India, the allium groups (onion and garlic) are important bulb crops for home consumption as well as sources of income to many peasant farmers in many parts of the country. The garlic bulbs are valued for their flavor and have wide applications in food and their antimicrobial, antifungal, insecticidal and antioxidative properties. The engineering properties of garlic bulb, clove and skin plays important role in the planning of various post-harvest operations like drying, sorting, grading, bulb breaking, peeling and designing the process equipments like bulb breaker, clove separator and peeler. The aim of this chapter was to study the engineering properties viz., physical, mechanical, aerodynamic and frictional properties of garlic bulbs, and cloves in both peeled and unpeeled form.

Introduction

India is rightly the spice bowl of the world. India has the largest domestic market for spices in the world. Indian spices are the most sought-after globally, given their exquisite aroma, texture and taste. Garlic (Allium sativum L.) is a world’s favourite, versatile horticultural commodity consumed for culinary, medicinal and antimicrobial purposes and is being cultivated for over 5000 years. The most important part of the garlic plant is the compound bulb. Each bulb is made of 6-26 cloves and is wrapped in a white papery sheath. Some varieties have a radish or purplish sheath. The bulbs are valued for their flavour, command extensive commercial importance because of their wide application in food and pharmaceutical preparations. Garlic is still probably nature’s most powerful medicinal plant to us today. It is recognized to have remarkable preventive and curative abilities. Garlic is mainly used aromatic spices and pickles as it has digestive, carminative and anti-rheumatic properties. It is being used in ayurvedic formulation since a long for curing lungs, healing the intestinal ulcer and checking muscular pain and giddiness.

Abstract

During present investigation a comparative study was done to see the effect of storage on physical properties of tomatoes (Lycopersicon esculentum Mill) packed in HDPE and stored under ambient temperature. Four varieties of tomatoes taken for current investigation were Badshah, Himshikhar, NS-524 and Raja. From the studies it was clear that TSS increased gradually during storage duration for entire tomato varieties due to loss of some moisture from tomatoes. Variety NS-524 shows maximum shrinkage among all during observation period.

Abstract

The chapter aims at introducing selected physical properties of food and biological materials in food process and application in the field of food technology. These physical properties of food are not only used for designing of food equipments but can also maintain the nutritive value of food to a greater extent during processing in these equipments.

Introduction

The investigation of food engineering is spotlighted on the inspection of equipments and system used to process food materials on a commercial scale. Building of system for food materials can be efficient if two factors are known, the nature of the food product and what happen to the food during its processing. Food materials are organic in nature and it has a certain kind of qualities which recognize them from other processed food product. Since food materials are organic in nature, they have (a) shapes usually found in normally non regular; (b) properties which differ from other food products; (c) heterogeneous arrangement; (d) properties are varied due to climatic conditions, ripening conditions, etc. and (e) several other factors such as (e) influenced by chemical changes, moisture content variation and enzymatic movement. Managing food materials with these remarkable attributes requires extra thought, for the most part by implication and extra sources or reasons for different varieties. The attributes of a food material that are autonomous of the on looker, quantifiable, can be measured, and characterize the condition of the material (yet not how it accomplished that state) are considered as its physical properties.

Introduction

Sem (Dolichos) bean, Hyacinth bean or Field bean is one of the most ancient crops among cultivated plants. It is a bushy, semi-erect, perennial herb, showing no tendency to climb. It is mainly cultivated either as a pure crop or mixed with finger millet, groundnut, castor, corn, bajra or sorghum in Asia and Africa (Maass et al., 2010). It is a multipurpose crop grown for pulse, vegetable and forage. The crop is grown for its green pods, while dry as well as fresh green matured seeds are used in various vegetable food preparations, as most of the nutritive value is concentrated in the seeds. FAO website reports that Dolichos lablab (field bean) is a dual purpose legume. It is traditionally grown as a pulse crop for human consumption in south and south-east Asia and eastern Africa. Flowers and immature pods also used as a vegetable. It is also used as a fodder legume sown for grazing and conservation in broad acre agricultural systems in tropical environments with a summer rainfall. Also used as green manure, cover crop and in cut and carry systems and as a concentrate feed.

Abstract

Quality assessment of fruits and vegetable before marketing and processing is an essential task. Various destructive and non-destructive methods have been investigated to achieve this goal. Among the several prevalent noninvasive methods, optical properties measurement methods also promotes for nondestructive quality inspection of fruits and vegetables. The optical properties of biological tissue are, therefore, very importance important for getting sample information and data quantification of the inside of the material. The main goal of this chapter is, thus, to introduce fundamental concept of optical properties, its principle and application in fruits and vegetables. The discussion of electromagnetic radiation for better understanding of the nature of light has also been explored.

Abstract

Thermal properties of food are its ability to conduct, store and lose heat. These properties are inherent in food processing and preservation practices. Thermal properties are important for modelling processes, engineering design of processing equipment, sterilization and aseptic processing. Important thermal properties are thermal conductivity, specific heat and thermal diffusivity. These properties depend on chemical composition, water fraction and temperature.

Introduction

Thermal properties are involved in almost every food processing operation. It is essential to have knowledge of thermal properties of foods which is important in analysis and design of various food processes and food process equipment involved in heat transport. Thermal properties of food are greatly depending on composition, temperature and density of food. Thermal properties required for heat transfer calculation include specific heat, enthalpy, thermal conductivity and thermal diffusivity. Thermal properties of foods are related to heat transfer control in specified foods and can be classified as thermodynamic properties (enthalpy and entropy) and heat transport properties (thermal conductivity and thermal diffusivity). Thermo physical properties not only include thermodynamic and heat transport properties, but also other physical properties involved in the transfer of heat, such as freeze and boiling point, mass, density, porosity, and viscosity. These properties play an important role in the design and prediction of heat transfer operations during the handling, processing, canning, storing, and distribution of foods.

Abstract

The electromagnetic processing instruments such as microwave is very commonly used at house hold level, hence understanding the behavior of food as well as factors affecting its dielectric properties becomes important. Dielectric properties (DEP) play an important in electromagnetic processing of food products and mainly depend upon the moisture content, physical properties, composition, temperature and power applied. Different methods have been used to determine the DEP of food material including parallel plate, coaxial probe, resonance cavity, transmission line and free space method. The selection of these methods is again based on several factors such as type of materials, accuracy of measurement, the scope of the research, frequency range, availability of equipments and resources. Present study thus summarizes the importance of DEP of food, influencing factors and the different measurement techniques.

Abstract

Rheological properties of dough from different flours are very important to know about the kneading and modeling process especially for development of bakery products. Rheological testing is helpful to examine the structural and fundamental properties of dough. The basic principle underlying evaluation of rheological properties are mechanical behavior of the dough, in conjunction with the physical structure of the dough, the molecular structure of the protein continuous phase in the dough and with chemical reactions of functional groups. This chapter presents some of the methods currently used in bakery industry for determining the rheological characteristics of the flour and the dough. The instruments such as Farinograph, Mixograph, Extensigraph, Alveograph and Amylograph, which are used for the measurement of dough rheological properties (due to visco-elastic behavior of dough) were described.

Abstract

The frictional properties such as coefficient of friction and angle of repose are very important in designing of storage bins, hoppers, chutes, conveyors, harvesters and threshers etc. Angle of repose is the angle made with the horizontal at which the material will stand when piled. The angle of repose is also important in designing the equipment for mass flow and structures for storage. The static angle of repose (b) was determined using an open-ended cylinder of 150 mm diameter and 250 mm height. The higher the moisture content, the higher the cohesion between the seeds. In terms of flow ability, the seeds are heavier and the inertia to move is increased. Coefficient of internal friction is the frictional resistance of seeds with each other. Coefficient of external friction is the frictional resistance between the seeds and the surface. The rolling resistance is directly proportional to the weight of the rolling object and to the coefficient of rolling resistance which is dependent on the rigidity of the supporting surface and indirectly proportional to the effective radius of the rolling object. The air velocity at which an object remains in a suspended state in a vertical pipe under the action of the air current is called terminal velocity of the object.

Abstract

The research work was conducted on the moisture dependent physical properties of kidney bean (White speckled kidney beans) were analyzed. Length, width, thickness varied between 1.53-1.90, 0.79-0.94, 0.58-0.76 cm for kidney beans, respectively. Arithmetic mean diameter and geometric mean diameter were 0.96-1.19 and 0.88-1.11 cm₂, respectively. Volume, Sphericity and surface area ranged between 0.44 -0.87 cm₃, 0.57-0.60 and 2.91-4.68 cm₂ for white speckled kidney beans, respectively. The kidney bean was soaked in normal water with initial moisture content 14.22 % (db) upto 270 min and attained the final moisture upto 83.23 % (ab).

Abstract

The knowledge of engineering (physical) properties constitutes important and essential data in the design of machines, storage structures and processes. The present investigation was carried out determine the physical parameter (diameters, mass, volume, density, sphericity, angle of repose etc.) of varieties KPS 10. The moisture content in green pea (KPS 10) was observed 411.77% (db). The average values of dimensional and geometrical parameter like length (D₁), width (D₂), height (D₃), AMD, GMD and SMD were found 9.517mm, 9.343 mm, 7.707 mm, 8.856 mm, 8.816 mm and 15.305 mm respectively. Mean values of mass of 1000 pea seeds, volume, bulk density and true density were found 329.501 g, 0.2 ml, 0.275 g/cm₃ and 0.304 g/cm₃ respectively. Average values of angle of repose, sphericity, porosity and moisture content were found 24.7, 0.926 %, 9.528 and 80.96%, respectively.

Abstract

Food processing involves the transformation of raw animal or plant materials into consumer-ready products, with the objective of stabilizing food products by preventing or reducing negative changes in quality. Without these processes, we would neither be able to store food from time of plenty to time of need nor to transport food over long distances. Food processing has also gained its importance in the wide variety of diet among people throughout the globe and availability of exotic food items at various places. Processing of food items enhance the taste, flavor and aroma of the food thereby increasing the overall chances of its acceptability among the masses. So, it is essential to determine and recognize the database of physical and engineering (aerodynamic and mechanical) properties of these agricultural products because these properties play an important role in designing and developing of specific machines and their operations such as sorting, separating and cleaning, also to determine the optimum in seed metering device in pneumatic planter and precision sowing machine to suite every size of these grains.

Abstract

Multi-commodity flours were prepared by blending rice flour, mung flour and potato flour with wheat flour in ratios of 0:0:0:100, 5:5:5:85, 10:10:10:70 and 15:15:15:55, respectively and packaged in glass jar, high density polyethylene and aluminium flexible packaging for biscuits development. The standardized formulations for biscuit had ingredients as 100 g flour/multi-commodity flour, 45 g sugar, 45 g hydrogenated fat, 1.25 g sodium bicarbonate, 1.25 g baking powder and 1.0 g curry leave powder. The biscuits were baked in convective baking oven at 180 > C for 10-15 min till baked. The well baked biscuits were removed from the oven, cooled to room temperature, packaged and stored under ambient condition. The physical quality (Mass, thickness, diameter, spread ration percent spread and bulk density), of biscuits were analyzed just after preparation under ambient condition. Results were also reported that the spread ratio of multi-commodity flour biscuits increased with decrease in the incorporation of wheat flour in multi-commodity flours. It is clear that spread ratio is mostly influenced by the diameter and thickness of biscuits.

In 1920, a 30-year-old Czech writer Karel Èapek, wrote a play called “R.U.R.” (Rossumovi Univerzální Roboti or Rossum’s Universal Robots). For this dystopian work about a bad day at a factory populated with sentient androids, Èapek called the androids “roboti”, as suggested byhis brother Josef, a painter and writer. It was premiered in Prague on 25^th January, 1921.

Èapek was admired for his opinions:

My dear Miss Glory, Robots are not people. They are mechanically more perfect than we are, they have an astounding intellectual capacity, but they have no soul.

But surprisingly he was keen on gardening!

EAAMs (Electric Agricultural Aerial Machines) have emerged from drones used for both aerial filming, as toys and even as racing units. A Price water house Coopers’ study revealed that the global market for drone-powered business solutions was valued at $127.3 billion in 2016. For agriculture, prospective drone applications in global projects were valued at $32.4 billion. Stelios Kotakis and colleagues at market research firm IHS Markit projected that there would be around 400,000 shipments of drones to firms in the agriculture and forestry sectors in 2017. The Food and Agriculture Organization (FAO) of the United Nations projects that by 2050 humanity’s ranks will likely have grown to nearly 10 billion people. Farmers will need to produce more with less, while preserving our environment for future generations. And society has a duty to help them achieve this. Although agriculture is perceived as a traditional economic sector, precision agriculture technologies have already boosted crop yields significantly in the last decades. The same study forecast that agricultural consumption would increase by 69% from 2010 to 2050.

This chapter traces the history of the electric quadcopter commonly known as the drone, prior to its use in agriculture.

As long ago as 1493, the versatile Italian Leonardo de Vinci, painter, sculptor, machine designer often inspired by his observations of Nature, made a sketch in one of his little notebooks of a screw-like machine next to which he wrote in his mirror-handwriting:

If this instrument made with a screw be well made – that is to say, made of linen of which the pores are stopped up with starch and be turned swiftly, the said screw will make its spiral in the air and it will rise high.¹

Four centuries later, in 1863, the Viscount Gustave du Ponton d’Amécourt, President of The Society for the Encouragement of Aerial Locomotion by Means of Heavier than Air Machines, published a forty-page monograph in Paris, entitled “The Conquest of the air by propeller. Account of a new system of aviation.” In this he took the Greek words helico and pteron, meaning “spiral” and “wing”, and combined them into the word hélicoptère (helicopter). D’Amécourt and his friends were among those very few who were passionately convinced that the future of flying was with heavier-than-air machines. To prove their point, having built a fragile flying machine model driven by clockwork springs, they watched it ascend vertically for a few seconds to a height of less than 3 metres (10 feet), only to crash back to the ground.

The 21^st century dawned with interest in the potential of electric agricultural machines. Beginning in 2000, a concept study, MELA Mobile Elektrische Leistungsund Antriebstechnik Mobile (electric power train technology)supported by universities and organizations in Germany as well as Fendt Agricutural Company (AGCO) showed a possible solution on tractor electrification with electric driven auxiliaries as well as electric CVTs and implement electrification. In 2003 the University of Hohenheim developed an electric combine harvester called Magda. With the introduction of a 42 VDC power supply system, the range of small rotational drives and servo motors could be covered. They showed that if more power had to be transmitted, threephase alternating current should be used since threephase machines had a large speed range and a large range of constant power.

During the first years of the century, longestablished transport manufacturers have been quick to see the environmental advantage of electric propulsion, be it with batteries, hybridelectric or fuel cell. With airliners, Boeing, Airbus and Tupolev quickly saw the advantage. With motorcycles, names such as HarleyDavidson, Curtiss, Ducati, Saroléa and Royal Enfield have positioned battery packs between two wheels. With trucks, Daimler, Toyota, Cummins, Peterbilt, DAF, Volvo, Leyland, Kenworth, and Isuzi, among others have taken the electric route. With buses, Alexander Dennis, Scania, Volvo, New Flyer, Van Hool, DAFVDL, Blue Bird, Heuliez, Rampinican carry their passengers more silently. It therefore seemed only logical that traditional agricultural machinery builders should make the same transition. The first to do this was John Deere, established in Moline, Illinois in 1837.

In 1920, although electric vehicles were not used on the American farms about 5,000 electric industrial trucks were produced by 12 American manufacturers, while estimates of the total fleet ranged from 6,000 to 15,000, most of them built during the war. Most used an exchange charging system. Among the manufacturers seen in and around cities and towns were the Commercial Truck Company, the Lansden Company, the Walker Vehicle Company (now owned by Commonwealth Edison), the Ward Motor Vehicle Company, the Steinmetz Electric Motor Corporation, Walter Motor Truck Company, and the Baker R L Corporation.One step away from agriculture, Charles A. Ward of New York City, was head of his family’s baking company, made up of the Mackey Company, the Ward Corby Company, the Ward Bread Companyand the Ohio Baking Company of Cleveland. In 1911, Ward had decided to replace his horse-drawn delivery vehicles with electric trucks, thus doing away with the unsanitary stable hitherto part of or adjacent to bakery.¹

Alongside this, the challenge of using stationary electric agricultural machines continued to be met. Two innovations which entered into dairy farming were the milk cream electric centrifugal separator and the surge milker. The Babson brothers (Henry, Fred and Gus) of Chicago were friends of and dealers for electrical battery inventor and entrepreneur Thomas Edison, and importers of Belgian-made Méllote separators. In 1916, the Babsonsproduced their own Pine Tree milking machine. While the overall design was similar to others, the electrically powered Pine Tree Pulsator outperformed any other pulsator made. These machines were powered by a 32-volt Delco system with 12 batteries near the barn. Pine Tree Pulsators were simple enough that the farmer could maintain them himself. The Pine Tree Pulsator was patented in 1921. The problem with this unit was that it was difficult to keep clean.

The domestication of oxen in Mesopotamia and the Indus Valley Civilization, perhaps as early as the 6th millennium B.C. provided mankind with the draft power necessary to develop the early plough into the larger, animal-drawn true ard (or scratch plough). Some of the earliest evidence of ploughing from around 2800 B.C.was found at the Indus Valley site of Kalibangan. Subsequent archaeological finds in Prague, Czech Republic, push the oldest known ploughed field even further back to 3500-3800 B.C. All food produce was planted and harvested by hand: seeds were scattered by hand and planted grains were brought from the field to be threshed on the dooryard. Milking a small herd of cows or goats was also done by hand. This continued for centuries. Then man discovered electricity.

In 1746, just a few years before Benjamin Franklin of Philadelphia sent a kite to catch lightning in a storm, a Doctor von Maimbray gave talk to the Royal Society of London where he described his experiment of electrifying the myrtle bush (Morella cerifera) which then put forth new branches in October, something which had never happened before. This news inspired others in Europe to carry out similar experiments. In 1749, Abbot Jean Antoine Nollet of the Royal Academy of Sciences in Paris France, inventor of the electroscope, published a pamphlet on “The Harmful Effects or Advantageous of Electrical Phenomena on Plants.”¹Isolated experiments continued until in 1783 Father Pierre Bertholon de Saint-Lazare of Montpellier published “About the Electricity of Plants”, a work in which he dealt with the effect of atmospheric electricity on plants, taking in their medicinal and nutritive-electrical virtues and but in particular the practical means of applying it usefully to agriculture.²He even built an electro-vegetometer, a device for collecting atmospheric electricity to distribute it in the soil and then to the plants, but he met with little success. Bertholon also conceived of subjecting plants to “electric rain” by connecting a large syringe to an electric source. A gardener, standing on a slab of insulating material in a wagon, carried a sprinkling can electrified by means of a wire leading to a static machine. “By means of this process, strange for the times, the good Abbé Bertholon, who was considered something of a sorcerer, obtained lettuces of an extraordinary size.”3