eChapters

Irrigation status at the national level
Out of the 140 m ha of net sown area in the country, 50 m ha ia under irrigation working out to a percentage of about 35. In the different states, the net irrigation per cent varies from 12 in Mizoram to as high as 90 in Punjab. Though at national level the contribution from canal and under ground water are almost equal, yet in Assam, Himachal Pradesh, Orissa and the other North eastern states, it is predominantly canal system, while in Gujarat , Punjab, Rajasthan and Uttar Pradesh and ground water predominates as the source. In Tamil Nadu, tank irrigation is an important irrigation source with almost Quarter of the irrigated area under this system. In the other southern states as well as in Orissa also tank system is in vogue to a considerable extent. The unscientific water use in both canal and lift irrigated commands has resulted in raising water table in the first case and fast receding ground water table in the second case. Thus, there is an imminent need for reducing the irrigation water application in agriculture with out affecting the yield and there by increasing the Water Use Efficiency (WUE) The options for increasing the water productivity/improve the WUE are discussed here.
Prevention of water losses in transportation system
Huge quantity of water is lost during the transportation of water from the source (reservoir/main canal! tank/ wells) to the field and till it reaches the root zone. Hardly 20 to 40 per cent of the water released reaches the root zone. The irrigation efficiency can be increased by the selection of proper method of irrigation along with proper design. Apart from the high evaporative and seepage losses occurring at the reservoirs and main canal, considerable amount of water is lost as seepage and evaporation in minors, distributaries, field channel etc. The losses occurring in a typical project in the alluvial plains as reported by the Second Irrigation Commission is given in table 2.

It is estimated that the country needs about 245mt of food grains, 30mt of sugar and jaggery, 7 lakh of tea, 1.7 lakh t of coffee, 10mt of vegetable oil and 17m bales of cotton. For realizing this, irrigated agriculture has to play an important role. To achieve this water use efficiency (WUE) in the irrigation sector has to be improved considerably as bulk of the available water is used in agriculture. But, with the ever-increasing population and industrialization problems, the demand for water by these sectors is bound to increase manyfolds in future. The requirement of water by different sectors during 2025 is estimated to be 105 m ham, which is 30 m ha m more than the present one. The share of water utilization for agriculture is expected to get reduced from the present percentage of 8~ to a value of 73 by 2025. Further, the demand for water for agricultural purposes is estimated to increase from 470 krrr’ to 740 krrr’ in a period of four decades (Table 1). During the same period there will be four­fold increase in the water demand for non-agriculture purposes.

5.1  Write True/False

Q.1    The null hypothesis H₀ is said to be composite if it does not specify the joint probability of x₁, x₂, ......, x_n completely.
Q.2    We may write null hypothesis as :
    H₀ : θΣ Ωθ_0-

Botany

The plant is highly cross pollinated due to heteromorphism and bees being the major pollinators.

Varieties: PKM 1 & PKM 2

Method of seed production : Seed to Seed.

Land requirement : Uproot all the wild and non specific moringa trees if any near the field within a radius of 1500ft. Good drainage facility is must for moringa.

Isolation requirement : A distance of at least 500 M is necessary for seed production.

Season : Early season (July August), Mid season (September), Late season (October -November). Best season is September October, so that flowering starts during summer which facilities better pollination and seed set.

Abstract

There is a consensus amongst the geoscientists that overall there has been progradation along the east and west coasts of peninsular India. However, the present day configuration of the coasts and some of the geomorphologic features such as absence of spit and delta along west coast and absence of major estuaries and petroliferous structures along east coast still remain controversial. The present study, based on the appreciation of certain geomorphological and tectonic features on Landsat imagery and aerial photographs of southern part of Indian Peninsula, suggests that the evolution of the coastline has been mainly controlled by tectonism.

The tapering nature of the coastline is attributed to the Precambrian orographic axis. The serrated nature of the post Precambrian coast line is due to the Precambrian transverse faults, whereas the serrated margin of the post Gondwana, Post cretaceous and post Tertiary coast lines are attributed once again to the Precambrian faults reactivated time and again. During the Quaternary period the coast line has undergone many modifications. The coast line attained sinuosity due to Pleistocene folding which is well manifested by river migration. The coast line was subsequently faulted and shifted with en echelon pattern due to N-S regional compression which is referable to the collision of Indian Plate with Tibetan plate.

A. Morphological Examination of Bacterial Samples
Introduction
Bacteria are most widely distributed, the simplest in morphology, the smallest in size and difficult to identify. They are prokaryotic and a few are photosynthetic. Most bacteria are only 0.5 to 2.0 μm in diameter. Bacteria are generally rod, spherical or curved shaped. Rod shaped bacteria may vary considerably in length, have square round or pointed ends and may be motile or non-motile. The spherical or coccus shaped bacteria may occur single, in pairs in tetrads, in chains or in regular masses. The helical and curved shaped bacteria exist as slender spirochetes, spirillum and bent rods (vibrios). In this exercise the ubiquitousness of these organisms will be demonstrated in the air and water, on body and in mouth etc.
Materials
1. Petri plates containing nutrient agar
2. Sterile cotton swabs
3. Sterile water blank
4. Tube of nutrient broth
5. Materials for simple staining

Abstract

Sesame (Sesamum indicum L.) is known as the king of oil seeds in India due to the high oil content (50-54%) of its seed. The purpose of this study was to evaluate morphology of sesame under high temperature stress. Seventeen released varieties of sesame (Sesame indicum L.) were studied during kharif 2009 under rainfed conditions. Analysis of variance on ten quantitative and qualitative traits was carried out. The mean, range, phenotypic and genotypic variation, heritability in broad sense and genetic advance were calculated.

Introduction
The Kashmir Valley, situated in the western Himalayas between latitudes 33°01'N and 35°00'N and longitudes 73°48'E and 75°30'E, spans an area of 4,920 square kilometers and sits at an elevation of 1,585 meters. This region is rich in water resources, featuring numerous lakes, rivers, and wetlands. The ecosystem benefits from a continuous supply of water from perennial glaciers, mountain streams, and a multitude of springs. It is estimated that more than Exclusively Distributed by NIPA GENX Electronic Resources and Solution Pvt. Ltd. New Delhi 6% of Kashmir's land surface is covered by various types of water bodies, enhancing the valley's natural beauty (Zutshi and Gopal, 2000). Whether from glaciers, springs, rivers, or lakes, the water in Kashmir contributes significantly to its picturesque landscape. The Kashmir Valley hosts a variety of 23 fish species, both native and introduced (Bhat et al., 2020). Cypriniformes, the largest group of freshwater fish, are divided into two main superfamilies: Cyprinoidea (carp like fishes) and Cobitoidea (loach fishes). This classification covers a wide variety of aquatic species, highlighting the extensive biodiversity within the Cypriniformes order (Nelson et al, 2016). The initial documentation of cold-water fish in India was provided by Hamilton in 1822. The Cobitidae family, known as true loaches, includes species such as Botia birdi found in the Kashmir Valley. The family Balitoridae, specifically the subfamily Nemacheilinae, in this region include two scaleless fish species earlier named as Cobitis vittata and C. marmorata by Heckel (1838) but Kullander et al. (1999) renamed them as Triplophysa marmorata and T. kashmirensis and Paraschistura punjabensis. Loaches are a fascinating subject for aquatic enthusiasts and researchers alike. Found predominantly in Eurasian waters, these bottom-dwelling fish are recognized for their distinctive elongated bodies, small scales, and barbels around the mouth which aid in their sensory and feeding functions. Loaches are renowned for their adaptability, thriving in a variety of habitats ranging from fast-flowing rivers to stagnant ponds. With over 200 species classified across several genera, loaches exhibit a remarkable range of behaviours and ecological roles, from the well-known clown loach (Chromobotia macracanthus), popular in the aquarium trade, to the stone loach (Barbatula barbatula), a species integral to the ecosystems of European rivers and streams (Nelson, 2006; Kottelat, 2012). Loaches play significant roles in their natural habitats, contributing to the benthic community dynamics and nutrient cycling. Their sensitivity to environmental changes makes them valuable bioindicators for assessing the health of freshwater ecosystems (Kottelat & Freyhof, 2007).

Objective

1. To know the morphology of different spices and condiments.

Materials: The crop of spices and condiments available at Horticulture research farm

Method of observation: Identification of various spices and condiments plants by carefully observing the root, stem, leaves, inflorescence, flower, fruit and seeds of the plants.

General

1. Habitat: A habitat is an ecological or environmental area that is inhabited by a particular species of plant. The term typically refers to the zone in which the plant lives and where it can find food, shelter, protection and mates for reproduction It is the natural home of a plant. Each habitat has its own particular type of climate like:
   1. Tropical Spices: These are grown at 1800 m - 3500 m height from ground level eg. clove, nutmeg, cinnamon, konkam, galangal, small cardamom, vanilla, black pepper, ginger, turmeric.
   2. Subtropical Spices: These are grown at 300 m - 900 m height from ground level eg. cumin, dill, fennel, coriander, fenugreek, onion, garlic
   3. Temperate Spices: These are grown at 900 m - 1800 m height from ground level eg. saffron, asafetida, caraway seed, celery seed, savoy, caper, balm, origanum, calamus, thyme etc.

Eventhough nematodes occupy nearly every habitat on earth, they are remarkably similar in morphology and life stages. Despite their structural complexity, certain basic principles are common to all nematodes. Nematodes are triploblastic, bilaterally symmetrical, unsegmented, pseudocoelomate, vermiform and colourless animals. The plant parasitic nematodes are slender, elongate, spindle shaped or fusiform, tapering towards both ends and circular in cross section. The length of the nematodes may very from 0.2 mm (Paratylenchus) to about 11.0 mm (Paralongidorus maximus). Their body width vary from 0.01 to 0.05 mm. In few genera, the females on maturity assume pear shape (Meloidogyne), globular shape (Globodera), reniform (Rotylenchulus reniformis) or saccate (Tylenchulus semipenetrans). The swelling increases the reproductive potential of the organism. Radially symmetric traits (triradiate, tetraradiate and hexaradiate) exist in the anterior region. The regions of intestine, excretory and reproductive systems show tendencies towards asymmetry. The nematodes have one or two tubular gonads which open separately in the female and into the rectum in the male which also have the copulatory spicules.

The free living saprophytic nematodes are generally larger in size. The animal and human parasitic helminths may have length of few centimetres to even a meter or more. The helminth parasitising whale fish is about 27 feet long. The study on these animals and human parasites are known as Helminthology.

Eventhough nematodes occupy nearly every habitat on earth, they are remarkably similar in morphology and life stages. Despite their structural complexity, certain basic principles are common to all nematodes. Nematodes are triploblastic, bilaterally symmetrical, unsegmented, pseudocoelomate, vermiform and colourless animals.

Guava is a fast growing evergreen shrub or small tree that can grow to a height of 3-10 m. It has a shallow root system. Guava produces low drooping branches from the base and suckers from the roots. The trunk is slender, 20 cm in diameter, covered with a smooth green to red brown bark that peels off in thin flakes. Young twigs are pubescent. The leaves grow in pairs, opposite each other. The leaf blade is elliptic to oblong in shape, 5-15 cm long x 3-7 cm broad, finely pubescent and veined on the lower face, glabrous on the upper face. The flowers are white in colour, about 3 cm in diameter, solitary or in 2-3 flower clusters borne at the axils of newly emerging lateral shots. The fruit is a fleshy, pyriform or ovoid berry that can weigh up to 500 g. The skin colour is yellowish to orange. The flesh can be white, yellow, pink or red, sour to sweet, juicy and aromatic. The fruit contains a variable number of seeds (about 3-5 mm long) and its mesocarp is characterized by the presence of small (0.1 mm) and hard fibrous structures called stone cells (sclereids), which may cause damage to processing machinery (Toma & Luchian, 2019).
3.1 Reproductive Biology and Pollination
Research on breeding systems in Psidium focuses primarily on P. guajava, which is an allogamous species characterized by an open pollination reproductive cycle. Nevertheless, self-pollination can occur. Bee-pollination, in which pollen is the sole reward, is the dominant pollination system in Psidium. Species of the superfamily Apoidea are important pollinators of both P. guajava and P. guineense. Both species are also pollinated by the European honeybee, Apis mellifera. Psidium guyanense, P. nutans, P. rostratum, and P. rutidocarpum lack comprehensive studies of their breeding systems, pollination, and dispersal (Sarkar & Sarkar, 2022).

1. Morphology of Bacteria
Structure of Bacteria
Bacteria are very small with a diameter of 0.5 – 1 μm in size. Due to this small size the surface area / volume ratio is very high compared to that of large organisms of similar shape. The large surface area compared to a small volume facilitates easy nourishment of all areas of the cell. So there is no circulatory mechanism to distribute the nutrients and there is little or no cytoplasmic movement within the cell.
i) Shape
Bacteria exhibit three types of morphology;
• Spherical - cocci (coccus) - Greek word kokkos, meaning a berry
• Straight rods - bacilli (bacillus) - Latin word bacillus, meaning a stick
• Helically curved rods -spirilla (spirillum)
Variations in these basic forms are also seen. Eg: cocobacillary, ovoid and filamentous.

Electrocardiogram (ECG)

Electrocardiogram is a graphic record of electrical events of the heart recorded by the electrocardiograph. It represents the sum up surface voltage and direction of electrical activity produced during cardiac muscle depolarization and repolarization plotted against time (Fig. 33). The time is represented on the X- axis (horizontal line) and amplitude of voltage is represented on the Y-axis (vertical line) of the graph. The potential difference occurring over the surface of the body (at different lead placement locations) is associated with depolarization and repolarization of heart muscle (myocardium). The amplitude of the potential difference is measured as milli volt (mV) and their duration is measured in second or milliseconds.

Bacteria are morphologically different. This characteristic is helpful in the identification of bacteria. Routine study of bacterial morphology should include examination of stained preparations. Motility should be examined by hanging drop preparation. According to the requirement, certain cell structures may be stained. Stained preparations should be made preferably from fresh agar slant cultures. Smears of Streptococcus should be made from a liquid culture. Morphology of bacteria may be described under the following terms:

1.Shape: Spherical, coccobacillary, short or long rods, filamentous, comma- shaped, curved or spiral forms.

2.Size: Spherical are measured in diameter and rod-shaped in length and breadth. Measurement is expressed in microns (µ).

3.Sides: Straight, concave, bulging, parallel or irregular.

4.Ends: Round, pointed, truncate or concave.

5.Axis: Straight or curved.

6.Arrangement: Singly, in twos, in groups of four or eight, in grape-like bunches, in long chains, or scattered irregularly, may be in bundles, angular arrangements or in Chinese letters.

7.Pleomorphism: Bacteria may differ from their typical shape. Some of the older cultures may depart greatly from their typical forms, and may show spindles, clubs, and filaments, swollen and branching forms. Variation may be both in shape and size.

8.Capsule: May or may not be present. When present, size should be noted. This requires special staining.

Most of the DNA of an living organism is packaged and organized in a chromosome as well as in mitochondria and cell organelles (Feulgen and Rossenbeck 1924). DNA is not found on its own but rather is structured in long strands wrapped around protein complex called nucleosome consisted of a protein called histone. During most of the duration of cell cycle a chromosome consists of long double helix DNA molecule (with associated proteins)During S phase the chromosome gets replicated resulting in X –shaped structure (chromatids) and still attached to a single centromere. The basic role of the chromosome is to provide a frame work which allows each linear segment of the genome to replicate and segregate efficiently. Failure in either of processes cause chromosome imbalance in daughter cells. Three specific cis-acting sites are required for stable chromosome maintenance, i.e., an origin of replication, a centromere and telomeres.

Classical studies of the morphologyof individual chromosomesof the plant species begun by S. Nawaschin 1910-16 and continued by Taylor (1925), Sharp (1929) and Mc Clintock (1929-30). And eventually it was possible to set up working models which account for the internal structure and chemistry of the chromosome and the genetic material as well as genetical facts. The use of aceto-carmine with iron (Belling, 1921) and application of heat greatly improved the staining differentiation of chromosomes. Smears have practically replaced the paraffin techniques of studying chromosome. The gross morphology of chromosomes is generally worked out either at prophase stages of meiosis or metaphase in somatic tissues. The chromosomes may differ in thickness, total length, position of centromere or spindle fiber attachment region, chromomere pattern and number and position of secondary constriction. The total length of chromosomes at metaphase also differs in different tissues of a species and also in certain tissues chromosome present may be very different in appearance. Figure 1 shows various morphological features of a eukaryotic chromosome

‘Integument’, the outer layer of insects consists of the ‘basement membrane’, ‘epidermis’ and the ‘cuticle’. One of the most important characteristics of insects is the presence of the rather hard, flexible chitinous exoskeleton or cuticle, which covers the entire body and provides support to the body. The exoskeleton of insects that is akin to the internal skeleton of vertebrates accounts for their size and shape. Movement is made possible by the division of the cuticle into separate plates or sclerites.  Primarily these  sclerites  are confined to segments and the sclerite of one segment is connected to the sclerite of the adjoining segment by means of an articulate called ‘suture’, a region in which the cuticle is very thin and flexible. The cuticle of each segment is divided into four primary sclerites viz., a dorsal tergum, two lateral pleura and a ventral sternum. The dermal glands present in the epidermal layer secrete the entire cuticle of the insect.

Like that of the body, the cuticular skeleton of the appendages is divided into tube-like segments connected to one another by articular membranes, thus creating a joint at each junction. Such joints enable the segments of the appendages, as well as those of the body to move freely.

In addition to the exoskeleton, an endoskeleton is also developed. This may be an infolding of the procuticle that produces inner projections or ‘apodemes’ equal to bones in vertebrates on which the muscles are inserted.

The insect body is made up of multicellular tissues. The body is bilaterally symmetrical and is covered by a hard, chitinous exoskeleton. The chitin at the junction of the segments is thinner and pliable and hence insects can bend their bodies. The exoskeleton is made up of several layers of non-living cells produced from the epidermis. Because of the hard chitin us exoskeleton of the body, the growth of the insect is affected beyond a certain extent. So, to facilitate further growth,, this exoskeleton is cast off a few times and this is known as ‘molting’. The number of moultings in a particular species is more or less constant.

Life forms are composed of one of two basic cell types : Eukaryotic or Prokaryotic. Generally, eukaryotic cells are larger and more complex than the prokaryotic cells and possess a membrane-enclosed nucleus; eukaryotic means ‘true nucleus’ (eu=true; karyon = nucleus). All plants, animals, fungi, protozoa and algae are composed of eukaryotic cells. Only the microorganisms classes as bacteria and the archaea are prokaryotic cells. Prokaryotic cells have no nuclear membrane and therefore lack a true nucleus. The latin prefix pro means ‘early’ and in this instance suggests the somewhat primitive nuclear structure found in bacterial cells. Eukaryotic microorganism are sometimes simply referred to as eukaryotes, and the prokaryotic microbes as prokaryotes.

A. General Morphology

2.1 The Root

It is the organ of a plant that typically lies below the surface of the soil.The root is best defined as the non-leaf, non-nodes bearing parts of the plant’s body. However, important internal structural differences between stems and roots exist. Root spices are, rather surprisingly, rare. Some popular examples of spices having roots are: Apium graveolens (Celery), Armoracia rusticana (Horse radish), Coriandrum sativum (Coriander), Ferula asafoetida (Asafetida), Glycyrrhiza glabra (Licorice), Levisticum officinale (Lovage), (Petroselinum crispum (Parsley), etc. All of the mentioned plants have aromatic roots.Roots of gingiberaceae are adventitious and storage roots arise from among the nodes of these scales.

Abstract

The coastal regions are always tectonically active since these form the junction between the continental and oceanic plates. These tectonic activities and the resultantly tutored fluvial and marine geomorphic processes and the independent fluvial and marine geomorphic processes carve out the coastal morphology. And if these coastal geomorphic features are studied, it will lead to the understanding of the morphotechtonics. One such a study carried out for a part of Ganjam coast, revealed various geomorphic anomalies viz: presence of high order hill ranges only in the north eastern and south western parts of the area with the central plain, northerly migrating Ganjam river, development of wide beach ridges only along the central plain, all indicating the Late Quaternary upliftment of the central plain.

Introduction

The Indian subcontinent is vested with nearly 9,000km long coastline both in its eastern and the western continental margins. These coasts provide unique configuration with convexities (land protruding into the coast), concavities (vice-versa), deltas of different morphologies, beach ridges and swales, bay mouth bars, peaks, serrations and projections in the shorelines, all indicating the vibrant tectonic, fluvial, marine and aeolian processes. As the coastal zones in general, form the boundaries between the continental and oceanic plate margins, these are inherent weak zones prone to tectonic activities, which in conjunction with other geomorphic processes, provide unique architecture to the coasts with above varied geomorphic features. That too, the Indian coasts were inferred to stand as testimony to the vibrant tectonic activities and other related geodynamic processes of the Quaternary period (Ramasamy, 1989; Ramasamy, 1999).

Mosaic is the combination of two or more raster images into single image. Sometimes, single image captured by remote sensing satellite doesn’t completely covers the desired study area mostly. Therefore, users resort for mosaicking two or more images captured by satellite sensors from different paths so that the whole study area is merged into a single raster image to facilitate the image processing and analysis. The pixel size of the raster images should be same for mosaicking.

In most of the cases, there is spatial overlapping among the raster images from which we want to create mosaic. These overlapping areas are handled in multiple ways which is being discussed further using R – code example. For mosaicking raster images in R, mosaic function of the raster package is used.

Purpose: In propagation of fruit plants by any vegetative methods such as cuttings, budding and in to the selection of ‘mother plants” and “bud-wood”. Use of bud-wood or any other propagation material from high yielding, true to-type, disease free trees (mother plant) will ensure uniform behaviour of trees in the orchard. If possible, propagation material from a single source is used.

Bud-wood used for budding purpose from high yielding, true-to-type and disease free trees certified for the above character by a certifying agency is referred as ‘certified bud’

Procedure: By adopting the flow sheet given below, clean scion from healthy, productive plants, can be selected for vegetative propagation.

1. INTRODUCTION

Motifs are patterns in biological sequences which can indicate the presence of certain biological characteristics and function. In general, these could represent patterns in any kind of biological sequences such as DNA sequences, RNA sequences and protein sequences. Evolutionary conserved regions (ECRs) are sequences with atleast 100 bp length alongwith minimum 70% identity, which includes most of the protein-coding exons, promoters, enhancers and repressors. ECRs are the preliminary step for finding TFBSs (Transcription factor binding sites) within the raw genome sequences of higher eukaryotes (large sizes of the genomes). DNA sequence motifs are short length, recurring patterns in DNA and are known to be associated with a biological function. These motifs sometimes indicate sequence specific binding sites for proteins such as nucleases and transcription factors (TF). Some sequence motifs are involved in biological processes at RNA level, such as ribosome binding, mRNA processing (splicing, editing, polyadenylation) and transcription termination. Motif identification is important at protein level for biological processes such as protein-subcellular localization, protein membrane, protein-protein interactions, identification of active site of enzyme(s) and post-translational modifications. Motif search is useful in understanding gene function, human disease, drug design, etc. Regulation of splicing in eukaryotes occurs through the coordinated action of multiple splicing factors. Sequence motifs are also useful in the study of genetic regulatory networks and regulatory program of individual genes.

Introduction

The motile bacteria show movements with the help of flagella. The motility of bacteria can be observed by hanging drop method under microscope.

Requirements

1. Bacterial culture
2. Cavity slide
3. Vaseline
4. Coverslip

Procedure

1. Place a very small drop of 24 hours old bacterial culture in the center of a coverslip.
2. Put a small amount of Vaseline at each cover of the depression side of the cavity.
3. Invert the cavity slide over the coverslip. The coverslip adheres to glass slide. When the coverslip is inverted, the hanging drop is suspended in the well.

Motivation represents the psychological force that drives individuals toward specific goals and behaviors, serving as the catalyst between intention and action. At its core, motivation encompasses the internal processes that energize, direct, and sustain human behavior over time. The term derives from the Latin word “movere,” meaning to move, which aptly captures its fundamental purpose of propelling individuals from a state of rest to purposeful activity. Contemporary organizational psychology defines motivation as the willingness to exert high levels of effort toward organizational goals, conditioned by the effort’s ability to satisfy individual needs. The essential elements of motivation form an interconnected system that transforms latent potential into observable behavior. The first element involves needs, which represent deficiencies or imbalances that create tension within an individual. These needs can be physiological,

Motivation of staff both in private and public organizations, leads to greater effectively leading to higher productivity and better performance. Motivation is the performance or procedure of presenting an intention that leads a person to capture some accomplishment (Quratul, 2011). Veterinary institutions like other organizations also seek to achieve better performance level. This requires providing motivation as an incentive or within the veterinarian as an individual to be self-motivated. There is a good scope for veterinarians to be more committed to work. McGregor argued that management has the responsibility to ensure that the productive elements of the enterprises are organized, such as money, materials and people with the purpose of meeting economic ends. People have an inborn dislike to work and tend to avoid it whenever an opportunity arises. It is also observed that people are born selfish; indifferent to the needs of the organization; hence people’s efforts need to be directed through coercion, controlling their action and modification of their behaviors to attain organizational goals. Hence, people in the organization need to be directed to take responsibility. To achieve organizational objectives, people need to be persuaded, rewarded, coerced, controlled, directed or threatened with punishment. While another theory is opposable to it. It is believed that if vets are motivated they would reach greatest potential. As extension specialist we need to motivate our peer and farmers aiming to improve performance and increased satisfaction.

Abstract

Motivation is a process that starts with a physiological or psychological deficiency or need that activates behavior or a drive that is aimed at a goal or an incentive. Motivation is a complex area. It’s different for different persons. Alignment of aims, purposes and values between staff, teams and organization is the most fundamental aspect of motivation. Organizational work culture and employees behavior are two important factors in taking decision on motivation techniques to be followed in the organization. Security of job, reward on better performance, importance of employee’s view in decision making, positive attitude, decisive leadership, etc bring motivation among employees. The five practices such as get to know every employee, challenge them to improve the performance, treat each employee as client for a day, establish great idea award and implement the great idea in organization activity, can improve the motivation of employees. They should be considered as resources, trusted by giving responsibility and rewarded with performance bonus for better motivation in the workplace.

3.1 Introduction
The different moulding machines are listed below.
• Thermoforming moulding
• Injection moulding
• Compression moulding
• Transfer moulding
• Extrusion moulding
• Blow moulding
• Rotational moulding
• Hydroforming
• Laminating
The melting furnaces, which feed molten metal to fill mould cavities are listed below.
• Cupola furnace
• Induction furnace
• Open hearth furnace
This chapter presents the different moulding machines and melting furnaces.
3.2 Thermoforming Moulding
To develop unique packaging solutions, thermoforming is the process of stretching a heated plastic sheet over a mould, then trimming, and assembling the design once the sheet has cooled as shown in Fig.3.1. The hot thermoplastic is stretched over the surface of the mould using the two thermoforming processes, viz. vacuum forming and pressure forming. A thermoforming machine is a sizable piece of industrial machinery that allows us to vacuum-form a plastic sheet onto an object as the sheet is being moulded. Thermoforming machines are used and benefited by a variety of businesses to efficiently package their products. The material used to produce parts by thermoforming machines is thermoforming plastic. Numerous thermoforming polymers are available for use in particular applications.

17.1 Introduction
The most important device that helps or supports the silkworms (larvae) for comfortable spinning their cocoon is called cocoonage or mountage. It determines both the quality and quantity of the cocoons. Different types of
cocoonages are used in different parts of India. In general, these are made of wood, bamboo, cardboard, plastic, grass, dry leaves, twigs, etc.
Mounting is an essential step in the rearing of silkworm. Mounting indicates the transition of silkworm from larval stage to pupal stage where it prepares to spin cocoons. Mounting is a process where fully grown (specifically 5th instar) silkworm larvae are picked and mounted in a suitable place (mountage) where it is about to spin. Mounting is a pivotal phase in silkworm rearing.
The following are the objectives of mounting:
1. To provide an ideal space for silkworm larvae to spin,
2. To ensure good quality cocoons,
3. To minimize mortality among silkworm by avoiding overcrowding,
4. To ensure a maximum silk production.

Introduction
From the tiniest insects to the largest blue whales, all species in the animal kingdom have been shown to undergo the migration. Millions of animals embark on epic journeys every year in search of food, shelter, and opportunity for mating. These animals routinely travel thousands of kilometres by land, sea, or air, which both tests and improves their endurance. Among the most striking animal migrations are those of Arctic terns. The long-distance migration of these little birds from pole to pole is well-known. They are thought to move over 40,000 kilometres (25,000 miles) a year, spending the majority of their time at sea chasing an endless summer. One of the most well-known migrations is that of the monarch butterfly, which travels across several generations. Though they are widespread throughout the United States and beyond, monarch butterflies are most known for their ability to travel 4,800 kilometres (3,000 miles) from Canada to Mexico. Millions of monarch butterflies fly south each year from their northern ranges to the oyamel fir forests near the Sierra Madre mountains, where they build massive roosts to remain warm throughout the winter. The monarchs begin their annual migration northwards in the spring, taking three to five generations to reach their goal. The migration that is the most dramatic belongs to the wildebeest. They coexist with thousands of zebras and gazelles in enormous herds that number over a million. The yearly migration of wildebeest across Tanzania and Kenya in quest of new water and grazing land is well-known. One of the most magnificent displays of nature is thought to be the migration. Animals that migrate are essential to preserving ecosystem balance and sustaining life as we know it. They distribute seeds and serve as pollinators, which support the structure and functionality of ecosystems.

ABSTRACT

The coconut eriophyid mite, Aceria guerreronis Keifer is a serious pest of coconut in Kerala, Tamil Nadu, Karnataka, Andhra Pradesh, Orissa, West Bengal, Maharashtra and Gujarat. The mites reside underneath the perianth of nuts and feed on the soft meristematic tissues of the young nuts. Their feeding damage is evident as scars on the surface of the older nuts. The damage results in reduction in size of nut and increases labour for dehusking the nuts.

The way a chemical moves, persists, and behaves in its surroundings is known as its behaviour. A chemical’s behaviour will dictate both its residual properties and field efficacy. The behaviour of insecticides is determined by their chemical and physical characteristics as well as the interaction of environmental elements. Our capacity to comprehend and forecast how insecticides will behave in the environment will determine our ability to keep utilizing insecticides.

Important features of systemic insecticides

1. They are not susceptible to wash off by rain

2. By virtue of their movement inside plants, they can afford to protection to regions where they have not been sprayed

3. They are often been transported towards region of growth

4. Since they have very weak contact action, safe to beneficial organism.

The hybrid breeding program in pigeonpea is unique and the first among the food legume. The concept of hybrid in this crop was conceived in 1974; and it is based on a small window of natural out-crossing present in the crop. This natural out-crossing in pigeonpea is mediated by a range of flying insects, which forage on large bright colored flowers of the crop in search of nectar and in the process affect the cross-fertilization. In the last 40 years a lot of basic and applied research has been successfully completed and over 50 research papers have been published in national and international journals of repute. A coordinated effort of scientists of different institutions has led to the release of two hybrids, one for central and another for peninsular zone of India.

1. Country Background

Mozambique is a country that is extremely dependent on agriculture, both for rural livelihoods and for overall economic growth. This importance is illustrated by the following:
    •    The agriculture sector accounts for about 20  per cent of GDP1.
    •    80  per cent of total employment and higher in rural areas.
    •    55  per cent of household incomes (national average) adding self-consumption and income from selling agricultural products2.
    •    40  per cent of export earnings (2003).
    •    The economy is not diversified and the average level of education is low, with few options for finding non-farm employment and incomes in rural zones.

Messenger RNA (mRNA) vaccine was the first authorised vaccine developed using mRNA vaccine production technology, against SARS-CoV-2. Well accepted by the population, it proved to be a major life saving intervention during the COVID-19 pandemic. This article discusses the mRNA vaccine technology and its major advantages, and provides an update on the various ongoing and completed clinical trials on the leading mRNA vaccines against various viral diseases. It also delves into the prospects and the technical challenges associated with the manufacturing of mRNA vaccine and the issues with its deployment in the low- and middle-income countries around the world. Despite the already available classical vaccine candidates, the persistent interest and continuous research in mRNA vaccine technology and the related storage, immunogenicity and lipid nanoparticles delivery aspects have helped in expanding and upgrading the vaccinology arsenals to counter diseases. The technology holds promises in opening new vistas to protect against infectious diseases and the associated complications, where safe and effective immunisations are currently lacking. Furthermore, as mRNA vaccines evolve, they offer new hope against neglected and reemerging diseases like rabies, Zika, and Nipah viruses. The flexibility and rapid adaptability of this platform underscore its potential to address unmet medical needs, laying the groundwork for universal and multi-pathogen vaccines, vital in averting future pandemics. Enhanced by advancements in nanotechnology and innovative delivery systems, mRNA vaccines are poised to revolutionise infectious disease prevention, cancer treatment, and genetic disorders, marking a new era in vaccinology and offering hope for global health challenges through continued investment in research and infrastructure.

MS-ACCESS is a very powerful RDBMS (Data Base Management System) which manages data in term of special table called relation. Using MS-ACCESS you can manage all your information from a single database file. Database files are stored with extension. MDB.

ACCESS stores information in the form of tables and you build your database on its basis. Each row in a table holds all information’s & for a particular person it is called a record. And each column contains different pieces of information regarding that person, like Roll No, Name, Class, Address etc. Same as MSACCESS involves.

In ACCESS, you have few things known as Forms, Reports and Queries. They allow you to check and get desired information as and when required.

15.1. Minimum Support Price (MSP)

MSP are announced by GOI at beginning of sowing season for certain crops on basis of recommendations of CACP.

MSP is price fixed by GOI to protect producer - farmers against excessive fall in price during bumper production years.

Guarantee price for their produce from the Government.

Objectives are to support farmers from distress sales and to procure food grains for PDS.

In cell biology, a mitochondrion is a membrane-enclosed organelle found in most eukaryotic cells These organelles range from 0.5–10 micrometers (µm) in diameter. Mitochondria are sometimes described as “cellular power plants” because they generate most of the cell’s supply energy in form of adenosine triphosphate (ATP), used as a source of chemical energy. In addition to supplying cellular energy, mitochondria are involved in a range of other processes, such as signaling, cellular differentiation, cell death, as well as the control of the cell cycle and cell growth. Mitochondria have been implicated in several human diseases, including mitochondrial disorders and cardiac dysfunction, and may play a role in the aging process.

Several characteristics make mitochondria unique. The number of mitochondria in a cell varies widely by organism and tissue type. Many cells have only a single mitochondrion, whereas others can contain several thousand mitochondria. The organelle is composed of compartments that carry out specialized functions. These compartments or regions include the outer membrane, the intermembrane space, the inner membrane, and the cristae and matrix. Mitochondrial proteins vary depending on the tissue and the species. In humans, 615 distinct types of proteins have been identified from cardiac mitochondria; whereas in Murinae (rats), 940 proteins encoded by distinct genes have been reported. The number of proteins encoded in plant mitochondrial DNA is probably not much higher than the number encoded in mammalian mitochondria.Experiments have shown that most of the protein synthesis in isolated maize mitochondria can be accounted for by some 18-20 polypeptidesThe mitochondrial proteome is thought to be dynamically regulated. Although most of a cell’s DNA is contained in the cell nucleus, the mitochondrion has its own independent genome. Further, its DNA shows substantial similarity to bacterial genomes.

ABSTRACT

Green revolution provided sufficient amount of foods but the way resources were utilized causes the degradation of natural resources in various aspect. The adverse effect on the ecological system can be visualized in the form of various diseases in human and loss of biodiversity. The population burst is the root cause of imbalanced ecological system because agricultural land decreases drastically. Therefore we must aim to develop and improve the agri- economic growth of farmers by introducing elite variety of Mucuna pruriens (L.) DC. M. pruriens, a member of Fabaceae family, is an adaptogen and known for its tonifying, strengthening and all around beneficial properties from every part of the plant. M. pruriens has range of medicinal applications, because of unusual amino-acid L-DOPA (L3, 4dihydroxyphenylalanine) a precursor of neurotransmitter dopamine (Anti Parkinson’s) and involved in various secondary metabolite pathways. It acts like aphrodisiac, anti-snake venom, anti-depressant, antidiabetic, anti-microbial. It has a nutritional quality comparable to soyabeans. M. pruriens exhibits a tolerance for various kinds of environmental stresses such as drought, low soil fertility, and high soil acidity. M. pruriens suppresses weeds through indeterminate growth and large leaves reduce the amount of light for weeds. It shows allelopathy and effective in lowering nematodes. M. pruriens is used as forage, fallow, green manure prevents the soil erosion. It has a longer time span to be used in rotations for management of various pathogens.

Abstract

Mulberry is a fast growing deciduous woody perennial plant. It has a deep root system. the leaves are simple, alternative, stipulate, petiolate, entire or lobed. The number of lobes varies from one to five. Plants are generally dioecious. Inflorescence is catkin with pendent or drooping peduncle bearing unisexual flowers. Inflorescence is always auxiliary. Male catkins are usually longer than the female catkins. Male flowers are loosely arranged and after shedding the pollen, the inflorescence dries and falls off. These are four presistent parianth lobes and four stamens implexed in bud. Female Inflorescence is usually short and the flowers are very compactly arranged. There are four presistent parianth lobes. The ovary is one-celled and the stigma is bilid. The chief pollinating agent in mulberry is wind. Mulberry fruit is a sorosis, mainly violet black in  colour. 

6.1 Introduction
India’s mulberry plants, which are vital to sericulture, are susceptible to a range of pests and diseases that can harm them and reduce their productivity. The Leaf Roller, Mealy Bug, Whitefly, and Stem Borer are important pests that harm leaves and stems and lower plant yield. Plant degradation and leaf discolouration are caused by common diseases such as Powdery Mildew, Leaf Spot, Root Rot, and Bacterial Blight. To preserve healthy mulberry harvests and continue to produce silk, effective management requires the application of Integrated Pest Management (IPM) techniques, which include biological, chemical, and cultural approaches.
Mulberry is also prone to a number of illnesses brought on by bacteria, mycoplasma toxins, and fungi. It is simple for a perennial agricultural plant to become vulnerable to different diseases. Similar to this, pest insects have a
plenty of food available to them all year round to aid in reproduction. Therefore, developing high-yielding types through plant breeding programs is just as vital as preserving mulberries from disease and insect attacks. The diseases listed below are accompanied with control methods. Adopting appropriate management techniques will help prevent pests and diseases while producing high-quality and productive mulberry leaf.

2.1 Introduction
Growing as a perennial tree or shrub, the genus Morus (Mulberry) is employed in sericulture and is the only food source for the tamed silkworm Bombyx mori L. It is also a valuable commercial plant. The mulberry attracts silkworms because it contains elements that cause biting and swallowing. People who live in Karnataka, Andhra Pradesh, the northeastern states and other parts of India rely heavily on sericulture, which grows exclusively mulberries and their variants for the purpose of raising silkworms.
2.2 Mulberry Plant
Mulberry is a plant that belongs to the kingdom Plantae, order Rosales, family Moraceae and genus Morus. It grows quickly when young but eventually slows down and rarely reaches a height of 33 to 50 feet. The leaves are alternately arranged, simple often lobed and typically lobed on juvenile shoots rather than on mature trees. The plant can be monoecious or dioecious depending on the species. It produces multiple fruits that are 2-3 cm long and mature fruits that are white or green to pale yellow with pink edges. In most species, the fruits are red when ripened, turning dark purple to black and possessing a sweet flavour.

Genus : Morus 
Species : alba, nigra, rubra L.
Chromosome No. : 2n=28  
2n=42  2n=28 (56, 84)

Plants are ornamental and fruit bearing trees have wide adaptability. Plant loves to grow on garden soils but also grow or rocky and marginal soils. The number of species is disputable but two species are native of North America. Mulberries are usually cultivated as food or for rearing of silkworms and for the edible fruits. The silkworm mulberry is M. alba and fruit bearing mulberry is M. rubra. In India and elsewhere mulberry is known primarily as a fruit bearing tree, although it is not yet planted extensively, though few trees around home ground are common. Mulberry is remarkable for its foliage and for variable forms. The extent of variability is so pronounced that several forms may be present of a single tree and different trees of the same species show distinct individual

This fruit plant is fast-growing when young, but soon become slow-growing tree thrive well under tropical, sub-tropical and temperate region. Mostly this crop is being cultivated for rearing of silkworm and wind break rather than fruit crop. This crop not specific with climatic requirement so can be grown in arid, marginal soil, barren land without much care.

The different plant parts viz., stem, bark, twigs, leaf, fruit etc are being utilized in different ways. Stem use for making agricultural implement, house artisans’, sports items, fodder for animals and fruits use as fresh dessert and in processing for making of different value added products like jam, beverages etc. Apart from these, its different plant parts also have medicinal properties use mainly in folk, ayurvedic and unani medicines.

• The most important use of mulberry leaf is rearing of silk worm for production of silk.
• The mulberry tree is used for landscaping in Asia, Europe & Southern U.S A.
• Morus alba (White mulberry)
• Morus rubra (Red mulberry) is native to America.
• Morus nigra (Black mulberry)
• Mulberry plants are monoecious in sex expression.
• Inflorescence of catkins.
• Major mulberry producing countries; China®India®brazil
• The most extensive area under mulberry cultivation in India is in Karnataka.

  Major mulberry growing Indian states are: TN.→Kerala → U.P.→ Bihar→ Madhya Pradesh→W.B.→Rajasthan.

The word mulch was coined by Wagganor in 1960. It is derived from the German word ‘molsch’ means “easy to decay,” and mulches have widely been used for vegetable production since ancient times (Lightfoot 1994). Therefore the term mulching refers to the practice of covering the soil surface with different organic and inorganic materials, known as mulch materials to reduce moisture loss, balance wide variations in diurnal soil temperatures especially in the root zone, control weeds, insect-pests and diseases and finally enhance crop yield (Nalayini 2007; Kader et al. 2019).