eChapters

Introduction

The science of hydrogeology is defined as hydrology with emphasis on geology. This chapter is to refresh your geology knowledge. The key words are highlighted to assist a quick review.

The Crust and its Composition

The thin outermost layer of the earth is called the crust and ranges in thickness from about 8 km under the oceans to about 25 km on land. It extends under both oceans and continents, and forms the source for all the soils, vegetation, and gases in the atmosphere.

The crust is primarily composed of two elements: silicon and oxygen which account for 75% of the earth’s crust. Note that these are the two elements found in quartz (e.g., sand), which suggests this is the most common of all minerals.

Introduction

Large scale exploitation of groundwater using modern deep well boring technology and powerful pumps is the order of the day in India and elsewhere. Increase in agriculture area and year around cultivation of water intensive crops, frequently failing monsoons (Fig.5.1) all have led to drying up of surface water and increased dependence on groundwater.

Thus, given the scenario of over exploitation of the available groundwater, it is essential that proper storage and management of available groundwater resources be identified.

Introduction

Wells are vertical shafts excavated or holes drilled in earth to the level of water table for extraction. Digging of wells is an age old practice. Shallow dug wells supported communities in the past. Well water is drawn to the ground manually or mechanically using variety of containers made of metal, leather, canvass and wood or a combination of them. Draught animals or electrical power are used to draw water for irrigation.

Water table (Fig.6.1) wells extend below the groundwater table and extract free water. Pumping water from these wells lowers the water level. The well first gains water from the water bearing material in its immediate proximity. Subsequently a cone of depression is formed in the immediate vicinity of the well. Water outside the cone of depression but with in the area of influence is diverted to replace the body of groundwater finding its way in to pumping well.

Introduction

The need for water for human consumption and the industry keeps spiraling up in the cities in the wake of rural diaspora and urban sprawl. Groundwater is exploited at an unsustainable rate leading to depletion of aquifers. Worse still is the intrusion of salt water from adjoining coast into the aquifers leading to total wastage of remaining water.

Introduction

Fresh water, a renewable but not an infinite resource, is becoming increasingly scarce. The amount available for use to the world today is almost the same as it was 4500 years ago but global demand has been increasing exponentially. Since 1950, the renewable supply per person has fallen 58 percent as world population has swelled from 2.5 billion to 6 billion. Moreover, unlike oil and most other strategic resources, fresh water has no substitute in most of its uses. It is essential for growing food, manufacturing goods, and safeguarding human health.

According to a World Policy Forum report, the largest and most combustible imbalance between population and available water supplies will be in Asia, where crop production depends heavily on irrigation. Asia today has roughly 60 percent of the world’s people but only 36 percent of the world’s renewable fresh water. China, India, Iran, and Pakistan are among the countries where a significant share of the irrigated land is now jeopardized by groundwater depletion, scarce river water, a fertility-sapping buildup of salts in the soil, or some combination of these factors. Groundwater depletion alone places 10 to 20 percent of grain production in both China and India at risk.

Abstract

Increased human activities such as agriculture, mining, and manufacturing have resulted in rapid increase of green house gases (GHGs) in the atmosphere. Atmospheric accumulation of the GHGs results into global warming and climate variability or change. Climate change due to enhanced greenhouse effect arising as a result of human activity is considered a major global environmental threat to mankind today. Perhaps nowhere in the globe are people more vulnerable to climate change than in Sub-Saharan Africa (SSA). Most livelihoods in SSA are climate-sensitive due to over dependency on land and other natural resources and are thus perched on the brink of disaster due to climate change.

Climate change is now undoubtedly affecting millions of people across Africa and it actually threatens to wipe-out the past and current global efforts made to tackle poverty unless urgent and robust decisions and actions are taken. This is also a wake-up call for the world to adopt alternative development models that would ensure massive cuts in GHG emissions to avoid a potentially irreversible change. Scientists have warned that unless the global community, especially the developed countries, take genuine steps now to reduce their emissions; many more millions of people in the developing world will be negatively impacted by climate change.

Abstract

This chapter highlights the significance of irrigated desert agriculture as a prime cause of the settlement and welfare of nomads and the consequent reduction of conflicts over limited land resources. Um Jawaseer Desert Farm Project is located in Bayouda Desert, the Northern State about 200 km north of the capital Khartoum. The planning and management approaches of such irrigated projects were discussed with special emphasis on the participatory approach. In this respect the roles of the donor (NGO), traditional tribal institutions and the project beneficiaries were illustrated. The project beneficiaries were organized into the farmers, well and women committees. The environmental and socioeconomic impacts of the project were evaluated. The project maintained food security, improved nutritional status, hygiene, housing environment and assisted in the provision of primary education and basic health facilities. Cost/benefit analysis showed the high profitability of the project. Other positive impacts include conservation of the fragile environment and biodiversity and improvement of animal productivity. Consequently, the area which witnessed an out-migration, during the seventies and the eighties, due to drought and desertification is now experiencing incoming migration.

However, adaptation to the sedentary mode of life was a real challenge. The most striking benefits of the project was that of women training for the, involvement in the decision-making process and empowerment, since 20% of the land is allocated for women. In addition to that, problems like build up of salinity, sand encroachment, low organic matter content and increased susceptibility to some water-related diseases due to irrigation were tackled successfully.

Abstract

The desert environment is one of the most challenging environments for human habitation. Inhabitants have to deal with climatic factors such as high temperature, sandstorms, flash floods and lack of water due to low rainfall. The people of Saudi Arabian desert had developed various traditional adaptation approaches such as living in tents, wearing head dresses, settling close to source of water, using camel for transportation, irrigation farming and traditional land management (hema). In recent times, modern technologies for air conditioning, transportation and housing have replaced the traditional adaptation methods especially in the cities. The modern technologies have reduced the challenges faced by the traditional society but has thrown up new challenges to sustainability. The new issues include urban flooding, depletion of underground water, high energy demand and consumption and loss of natural habitat to urbanization. This chapter reviews the traditional and the modern adaptation techniques in Saudi Arabia especially in the urban areas. It examines the implication of the changes for urban sustainability and explores different approaches for reducing the negative impacts. The chapter also dwells on the role of geospatial techniques in adapting to the desert environment.

Introduction

Mango (Mangifera indica Linn.) is one of the most nutritious tropical fruits, native to Southern Asia and especially Eastern India. Mango belongs to Anacardiaceae family and it was disseminated all over the world in the beginning of sixteenth century, and there are currently around thousand known varieties of mango. It is the dominant tropical fruit variety produced worldwide, followed by pineapple, papaya and avocado, all of which are considered as major tropical fruits. Global production of mango in 2015-16 was estimated to be about 44 million tons, accounting for nearly 50% of world tropical fruit production.

Mango is the most important fruit of India and is known as “King of fruits”. Mango is cultivated in 2,312 thousand ha and the production is around 15.03 million tons, contributing 40.48% of the total world production. Main mango producing states in India are Uttar Pradesh, Andhra Pradesh, Karnataka, Bihar, Gujarat and Tamil Nadu. Total export of mangoes from India is 59.22 thousand tons, valuing Rs. 162.92 crores during 2015-16. India exports mango to over 40 countries worldwide. Major importing countries during 2015-16 were UAE, Bangladesh, UK, Saudi Arabia, Kuwait and Bahrain. Important mango varieties are Dashehari, Langra, Mallika, Amrapali, Bombay Green, Banganapalli, Totapuri, Neelam etc.

Introduction

Jackfruit (Artocarpus heterophyllus) is the largest edible fruit in the world. It is a seasonal fruit found in almost all the humid tropical regions of the world. It is very popular all over India and is believed to be of Indian origin. Flesh of jackfruit is starchy and fibrous and is a source of dietary fiber. Varieties are distinguished according to characteristics of the fruit’s flesh. In Kerala, two varieties of jackfruit predominate: varikka and koozha. Varikka has a slightly hard inner flesh when ripe, while the inner flesh of ripe koozha fruit is very soft and almost dissolving. Strong aroma of the fruit accounts popularity of its processed products. Each year, approximately 30-50% of the total harvested fruit is spoiled because of lack of post-harvest processing in India

Jackfruit has more protein, calcium, thiamine, riboflavin and carotene than banana. Edible bulbs of ripe jackfruit are consumed for their fine taste and pleasant aroma. The fibre content helps to protect the colon mucous membrane by decreasing exposure time as well as binding to cancer-causing chemicals in the colon. Fresh fruit has small amounts of carotenoid and flavonoid pigments such as ß carotene, xanthin, lutein and cryptoxanthin-ß. Together, these compounds play vital roles in antioxidant and vision functions.

The way technology is evolving, and the way it is changing our ways of living, why should we not be optimistic about technology. But then optimism comes tagged with pessimism. We aim for unfathomable optimum optimism. Technology is like water. It finds its open spaces. If it fills the available spaces more than it should, there is flood.

Future engineers and technologists are expected to appreciate, more than before, the human dimensions of technology. They are expected to have a grasp of the global issues. There is a need to understand the nuances of working in a culturally diverse space. According to some experts, good engineering designs should not be deprived of the benefits of a broad spectrum of life experiences, as adequate familiarisation with societal demands is essential for practical technological literacy.

Future engineers need to be better equipped to deal with people of diverse backgrounds, such as from social sciences, management, and communication. Some of the grand challenges that are enlisted, from an engineer’s point of view, are environment protection, hunger, energy and controlling the spread of the diseases. We need developers of responsible technologies and products.

We need managers to manage things, and at the same time we need adequate number of things to manage. There is a need to build faith in the public that engineers and technologists are sensitive to their concerns. One of the biggest responsibilities of the engineers and technologists is to keep themselves updated about professional developments and practices.

Countries, not only want exceptional scientists and engineers, but also people who are temperamentally innovators, and think they fit into their country’s core values. Many would say, prepare young minds and nurture future innovators.

Before carry out any ethnobotanical work, first define the goal of the assignment or study before selecting the approach, which best suits the interests, budget and schedule. Most of the methods used in ethnobotanical studies are time taking and costly because several field trips are required in several seasons for covering different ritual occasions and seasonal farming activities which are continue for a number of years for completion of an assignment. In this way, an assignment may be very long or short as per selection approach of an ethnobotanist. Long-term assignment or projects may be continue for several years and they require sufficient financial input. When sufficient financial add and time does not available to accomplished long term assignments, in that case a Rapid Ethnobotanical Appraisal (REA) can be done.

Major Families

This chapeter deals with indigenous knowledge on use of various plant species in traditional medicine, food, dye, wood and in tanning etc.

Malvaceae

The family Malvaceae is also known as Mallow family, characterised by mainly shrubs and herbs. The plants of this family frequent have stellate trichomes, persistant sepals, epicalyx present, stamens numerous and monadelphous, anthers monothecous, carpels 5 or more.

Abroma angusta (Devil’s Cotton)

Paste of the leaf is applied to heal wounds and to relieve joint pain or back pain. Young shoots are used as food. Roots are used to cure itching.

Abutilon indicum (Kanghi)

The whole plant is used to make brooms. Plant also has medicinal value and its sap is used against ulcer, leprosy, piles, dysentery and fever.

Introduction to DHAN Foundation

DHAN (Development of Humane Action) Foundation is a grassroots action agency working with poor communities in villages. Enhancing poor people’s livelihoods in sustainable way and enabling the poor communities are the focus of the programmes. The mission of the organisation is to build institute for innovation in the development work and reaching significance to bring positive changes in the lives of poor. DHAN Foundation was established in year 1997 as spin off institution of PRADAN (Professional Assistance for Development Action) based at New Delhi.

DHAN Foundation believes in building the capacity of people in planning, organizing, conflict resolution and implementation of development programmes. This will be possible only when people are encouraged to work on a single thematic focus, either through micro finance or small scale irrigation theme, for a substantive period to pick-up the generic skill of developing viable alternatives to their stalemate situation; DHAN Foundation initiatives are aimed at building people constituencies around specific activity, these institution will move into civic programmes like health, Education and Information Technology to address their member’s needs. Simultaneously DHAN Foundation as a mothering institution promotes thematic organizations as subsidiaries to upscale the matured themes and continue the promotional role to sustain the people’s organization in the specific theme for e.g. micro finance or irrigation.

2.1 Introduction

In a fiber optic sensor the heart of the sensor is an optical fiber. An optical fiber in its simplest form is a cylindrical symmetric structure consisting of a central ‘core’ glass/plastic of uniform refractive index and of diameter 4-600 µm. It is surrounded by a ‘cladding’ glass/plastic of slightly lower refractive index. To provide the mechanical and environmental protection to the fiber, the cladding is covered with an external plastic coating (seeFig. 2.1). The light in the fiber propagates by bouncing back and forth from the core-cladding interface. The design of the fiber optic sensor depends critically on the choice of optical fiber. Telecommunication fibers are inexpensive but may not be the right choice for sensors. Some of the fiber optic sensors dictate the use of application-specific optical fibers. In this chapter we shall first describe ray analysis for the light propagation in the fiber. The modes propagation, numerical aperture of the fiber, fiber characteristics and different kinds of optical fibers used for sensing will be described later.

Introduction

The acute food shortage was a major challenge in confronting the development of the country after independence with rapidly increasing population. Massive financial assistance of credit and subsidy under various rural development programmes unveiled by government could not yield desired impact on poverty and unemployment. The benefits of farm research did not reach the resource poor farmers. Several researchers indicated that the devolution of democratic decision-making at the village level was lacking.

The major task of bridging the gap between farmers and the scientific knowledge is in the hands of extension workers who should act as “conveyer belts” in communicating appropriate scientific knowledge and skills already available to the farmer in a smooth and acceptable form and in securing the adoption of these improved techniques. They must assess the intentions prevailing in the minds of rural people, their relationships and interactions, their groups, their institutions, their organizations and the culture, which influence the behaviour at large. They need to understand their motives, reactions, receptivity to new ideas, hidden resources of rural people and social and cultural obstacles prevailing in the society with their active participation.

To elucidate the hidden facts from the well-knit social, cultural and behavioral patterns, a family of approach known as “Participatory Rural Appraisal (PRA)” techniques is widely employed to understand the existing farming situations, problems, and opportunities in the rural areas. PRA techniques can also be used in evaluation and impact assessment in agricultural and allied enterprises and projects that can indicate the success and failure to plan for better future.

INTRODUCTION

In the world of flower, together with lilies, gladioli, begonias; the dahlias are one of the most important and popular flowering bulbs. With the blast of different colours, shape and sizes, dahlias bring life and beauty back to the landscape in late summer and autumn. The diversity of dahlias allows their usage in many different aspects due to huge range of flower types available and fairly easy cultivation.

In modern garden, dahlias are extensively used for exhibition, garden display and decoration. It can be grown in any form in the garden; in beds, in borders or even in mixed borders alongwith other plants. It grows well in pots also. For border purpose dwarf growing type are preferred while in pots usually large flowering dahlias are grown. The long stemmed flowers of various forms and colours are used in flower arrangement. Dahlias make excellent cut flowers, which typically last about a week in the house and are also used in making garlands.

The tubers of dahlias contain appreciable amount of insulin and fructose and small quantities of phytin and benzoic acid which are of medicinal and nutritional value. Flavanone 3-hydroxylase, which catalyses the conversion of flavanones to dihydro flavonols, was detected in flower extracts of cyanic strains of dahlia.

INTRODUCTION

Narcissus is a hardy or tender herbaceous perennial, growing from bulbs and seeds. In India it is commonly called Nargis. The splendid yellow and white flowers of the narcissus alone could make April and May month of delightful sweetness in the garden. Shakespeare mentioned Narcissus again and again as common symbol of the English spring. Narcissus are highly suitable for rowin in beds ots under the deciduous trees, window garden, etc. They are very good cut flower and are sold in the market. The bulbs of the European species are used in folk medicine as these are believed to possess the purgative, dermal and depurative properties. Few species are used for extraction of essential oil in France. There is often confusion as to whether the name narcissus or daffodil should be used. Popular thought attached the former name to the sweet scented tazetta or poet narcissus and the latter to the small wild Lent Lily which is still to be found massed in the wood and open pastures. Today daffodil usually refers to long trumpet and large flowered garden forms while, all the rest are narcissus. In the simplest words, the species of this are called narcissi, although the trumpets, which have trumpet (corona or cup) as long as or longer than the surrounding petals are usually called daffodils.

INTRODUCTION

Tulips are one of the most popular and widely grown flowering plant. Tulip is a main stay of spring gardens providing abundant flowers in vivid and vibrant spectrum and colours. It is first among bulbous ornamentals due to its attractive colours and exquisite flowers. Tulip is the national flower of Turkey and tulip motifs feature prominently in Turkish folk arts. The first European cultivation of the tulips as a garden flower occurred in the Netherlands in sixteenth century. In the following century, the early enthusiasm for the new flowers triggered a speculative frenzy now known as tulipomania. The Netherlands and tulips are still associated with one other. Tulip festivals are held in the Netherlands and in North America every May. A number of bewitching cultivars grown to perfection in a large variety of delicate and brilliant shades have developed tulip cultivation into a great bulb growing industry. Tulips are not only widely cultivated for cut flower production world wide but also grown for pot culture, in beds, borders, formal and informal location. They are also suitable for growing in orchards, lawns, rockeries and wild gardens.

The word tulip industry is dominated by the Dutch tulip growers. There is 10,000 hectare of tulip bulbs grown in the Netherlands. About 70 per cent of tulip bulbs cultivated are for forcing for flowers with 30 per cent for pre packs for gardens. The world market for bulbs has been buoyant for the past ten years. Production has been increasing at the rate of 6-8 per cent per annum and the market has expanded in line with this growth. In the Netherlands, three quarters of the total bulbs produced are exported, with the highest percentage going to the United State followed by Germany. In India, tulips are gaining popularity among the flower growers owing to congenial climate in hilly areas. Particularly in Kashmir valley, production of cut flower is increasing. Some area has been increased in Himachal Pradesh. It can also be grown successfully in other hilly parts of the country like Uttaranchal between 1300 to 3000 metre above mean sea level.

Abstract

The conventional methods of pathogen identification have often depended on identification of disease symptoms, isolation and culturing of the organisms, and identification by morphology and biochemical tests. The major limitations of these culture based morphological approaches, however, are the reliance on the ability of the organism to be cultured, the time consuming nature and requirement of extensive taxonomic expertise. Furthermore, diagnosis of plant diseases can be even more difficult with asymptomatically infected propagative materials such as tree grafting stocks or potato tubers. The use of molecular methods can circumvent many of these shortcomings. Accordingly, there have been significant developments in the area of molecular detection of plant pathogens in the last three decades. The polymerase chain reaction (PCR) which revolutionised molecular diagnostics and biological sciences. In the last decade the range of targets that can be diagnosed using diagnostic PCR have grown tremendously. The very flexibility and application specific variations in the basic theme of the system have allowed the development of many PCR variants adapted to wide range of applications. Furthermore, diagnostic PCR has been greatly improved by the introduction of the second generation PCR, known as the Real time PCR where closed-tube fluorescence detection and quantification during PCR amplification (in real time) is possible eliminating the need for laborious post-PCR sample processing steps which greatly reduces the risk of carryover contamination. Using Real Time PCR, it is possible not only to detect the presence or absence ofthe target pathogen, but it is also possible to quantify the amount present in the sample allowing the quantitative assessment of the number of the pathogen in the sample. Enumerating the pathogen upon detection is crucial to estimate the potential risks with respect to disease development and provides a useful basis for diseases management decisions. Crops can be attacked by many pathogens which, in addition, often occur in complexes. Therefore, many disease diagnostic applications require simultaneous detection and quantification of several targets. Methodological limitations, however, are in many cases the reason for developing simplex or assays designed for only few targets. The DNA Microarray technology, originally designed to study gene expression and generate single nucleotide polymorphism (SNP) profiles, is currently a new and emerging pathogen diagnostic technology, which in theory, offers a platform for unlimited multiplexing capability. It is viewed as a technology that fundamentally alters molecular diagnostics. The fast growing databases generated by genomics and biosystematics research provides unique opportunity for the design of more versatile, high-throughput, sensitive and specific molecular assays which will address the major limitations of the current technologies and benefit plant pathology.

Abstract

Health-conscious consumers are increasingly seeking functional foods in an effort to control their own health and well-being. The field of functional foods, however, is in its infancy. Claims about health benefits of functional foods must be based on sound scientific criteria. A number of factors complicate the establishment of a strong scientific foundation. These factors include the complexity of the food substance, effects on the food, compensatory metabolic changes that may occur with dietary changes, and, lack of surrogate markers of disease development. Additional research is necessary to substantiate the potential health benefits of those foods for which the diet-health relationships are not sufficiently scientifically validated. Research into functional foods will not advance public health unless the benefits of the foods are effectively communicated to the consumer. Finally, those foods whose health benefits are supported by sufficient scientific substantiation have the potential to be an increasingly important component of a healthy lifestyle and to be beneficial to the public and the food industry. Mounting evidence supports the observation that functional foods containing physiologically-active components, either from plant or animal sources, may enhance health. It should be stressed, however, that functional foods are not a magic bullet or universal panacea for poor health habits. There are no “good” or “bad” foods, but there are good or bad diets. Emphasis must be placed on over-all dietary pattern, which follows the current Dietary Guidelines, and is plant-based, high in fiber, low in animal fat, and contains 5-9 servings of fruits and vegetables per day.

Key words : Horticultural Resource Information System. INARIS.

Introduction

Wide ranging Indian climatic conditions are well suited for boosting production of a variety of horticultural crops (fruits, vegetables, flower/ornamental/medicinal and aromatic crops) which presently hold an important position in the global scenario. Development was at a very low ebb till the Third Five-Year Plan and increased significantly since the Seventh Five Year Plan (Rs.10,000 millions plan outlay). Government of India established National Horticultural Board (NHB) in 1984 and Agriculture and Processed Food Products Export Development Authority (APEDA) in 1986 to facilitate its larger development. The outlay is expected to increase even more in the Tenth Plan. Significant progress has been made in area expansion of different horticultural crops resulting in higher production. Besides, use of modern technologies has also brought about improvement in productivity. More than 50 per cent increase in production is seen in many of the horticulture crops during last one decade.

The efficient planning and implementation of different developmental programs on horticultural crops depends on production parameters like soil suitability, varietals dominance, marketable surplus, marketing channels, post harvest handling practices, cost of cultivation and market availability for sustained production. In addition, information on latest technologies developed by various research organizations on horticultural improvement, production, protection and post-harvest technologies are needed to be collected and made available to the scientists, planners and managers working in the related fields. But the available information on this aspect is scattered and the database is too weak to provide adequate support for developmental strategies. The digitization of comprehensive database on horticultural crops will definitely enhance the pace of increasing the area, production, productivity and promoting industry of horticultural crops that have taken lead in the new millennium with reference to nutritional quality of food and export potential. A strong, well-knit database to support need-based, market-driven and cost-effective horticultural development is imperative. Therefore, under National Agricultural Technology Project (NATP) a Mission Mode Sub-project on “Integrated National Agricultural Resources Information System (INARIS)” has been taken up to evolve a comprehensive computerized data management system on various agricultural resources like crops, animals, fishes and natural resources by harnessing RDBMS and GIS. The Co-operating Center at Indian Institute of Horticultural Research, Bangalore has developed the “Horticultural Resources Information System” with the objectives of (i) integrating existing databases in horticulture, (ii) designing and developing a comprehensive database in horticulture and (iii) developing resource maps of major horticultural crops in the country by integrating attribute and spatial data through GIS. In addition to simple storage and retrieval it will include other functions such as manipulation and dissemination of information to various users. This database will be integrated with 13 other Co-operating Centers dealing with different agricultural resources through a virtual private network (VPN). The Lead Center at Indian Agricultural Statistics Research Institute, New Delhi provide warehouse facility with a capability to analyze the data variously and provide report as cubes, tables and graphs to form a national database to cater to the needs of the users through a website. The facility of retrieving information as value-added maps using GIS will also be built in.

Key words : Wasteland Reclamation, Poverty Indicators, Food Insecurity, Alternate Livelihood Systems, Rural Infrastructure Index.

Introduction

The countries of Asia and the Pacific region accounts for nearly two-thirds of the chronically poor and undernourished in the world. FAO estimates indicate that, by 2010, Asia will still account for about one-half of the world’s malnourished population (FAO 2000). In Asia, poverty has mainly been rural phenomenon and nearly three-fourth of the poor live in rural areas, with large majority of them dependent on natural resources for employment and income. South Asia, which had a poverty incidence of 43 percent (or about 520 million people), contributed about 40 percent of the world’s poor. Development of natural resources thus offers a potentially enormous means of poverty reduction.

In developing countries poverty and environmental deterioration are often viable in proximity to each other, and have led many to infer that a two-way causality exists between human and environmental degradation. Environmental degradation usually occurs when production and consumption activities of growing population irreversibly weaken nature’s recycling capabilities. These economic activities are also attributed to the development of markets, the advent of modern technology, and the spatial integration of inaccessible areas to market systems. In many developing countries, however, environmental degradation such as soil erosion, deforestation and pollution are most visible around poor settlements, leading some policy makers to highlight the direct links between poverty and the environment.

One has to recognize that both poverty and the environment are descriptions of states of human and natural resource attributes and cannot be reduced to simple one-dimensional cause-effect relationships. Apart from conceptual difficulties in modeling linkages, another handicap has been the absence of adequate or reliable data sets on poverty and environment characteristics. The challenge for operational research is exploring how circumstantial evidence and inductive logic can be used to explain the nature of interactions between the two states. Based on nationwide wasteland statistics vis-à-vis state and district wise poverty estimates available with the concerned agencies, this study is one such attempt, and evaluates the incidence of poverty with the backdrop of natural resources degradation and role of institutional interventions with illustrations from India.

This chapter documents shoreline changes of the Dakshina Kannada and Udupi districts of Karnataka State for the period between 1967 and 2005 studied by comparing the SOI topographic maps with IRS-1C/1D LISS-III satellite imageries through GIS techniques. Examination of coastal geomorphology, sediment flux and effectiveness of seawalls had indicated that the 130km long coastline of Dakshina Kannada and Udupi districts is essentially stable, but for seasonal variations. It has been estimated that, out of 130km, about 55km long coast is vulnerable to sea erosion, of which, 25km is covered byseawalls and covering another 10km length underway. It is revealed through field examination that protection of coastline through these measures is satisfactory only along few patches while other stretches of seawalls simply shift the zone of erosion to adjacent coastline owing to many reasons including quality of construction, unscientific positioning of seawalls, etc. It is also inferred that same is the case of many other coastlines elsewhere including Kerala coast. These experiences warrant scientific design and implementation of coastline protection measures.

INTRODUCTION

The 130km long coastal zone of Dakshina Kannada and Udupi districts is one of the densely populated coastal zones of India. The coastline is almost straight, regular and oriented towards N22°W, N12°W and N6°W directions at south of Mangalore, north of Mangalore and north of Malpe respectively. Barrier beaches and spits, ancient beach ridges, marshes, swamps and tidal flats characterize this zone. Natural features and man-made structures interrupt the shoreline. The natural features include estuarine mouths of Netravati-Gurpur rivers near Mangalore, Mulki-Pavanje rivers near Mulki, Udyavara river near Malpe, Sita-Swarna rivers near Barkur, Kollur-Chakra-Haladi rivers near Kundapur and rock exposures near Someshwar, Surathkal, Mulur, Kapu and north of Malpe (Fig. 1). The man-made structures include one major and four minor ports; breakwaters at the Netravati-Gurpur estuary, New Mangalore Port and Malpe harbor and a number of seawalls placed at various places along the coastline (Fig. 2). All these structures/features bring about local irregularity and contribute to erosion and accretion along the shoreline to some extent. Apart from these, source of beach material, coastal processes like wave refraction, longshore current, littoral drift etc.

2.1 Introduction

Topographic expression is the replica of geological structures present within the earths surface. When various types of rocks of an area are displayed on a map (sheet of paper), it is known as Geological Map. Normally geological maps prepared on topographic maps. Surface topography is best presented by contour lines on a plain paper.

The importance of geological maps is to understand the nature of structure and distribution of surface outcrops with their relation to contour lines. Horizontal and dipping beds are easily identified on map because, horizontal beds runs parallel to contour lines while inclined beds cut through different contours. The angle and direction of dip can be calculated from geological maps. Geological maps are of great importance to civil engineers, after studying geological maps and consultation with geologists, civil engineers can advice for construction of engineering structures like excavation of road cuttings and construction of canal, bridges, dams and tunnels etc. Geologists get vital clues about the geological history of an area, and can draw a cross section of an area and know the structure present underground.

Abstract

Landslides have become a recurring phenomenon in most of the mountainous regions of the world. In Indian peninsular, the landslides which were mostly confined to the tectonically active Himalayan Mountains once, have started spreading over to the other mountain belts of the Peninsula. The Tirumala – Tirupati hills, which is drawing millions of pilgrims from all over the world is facing landslides especially along the newly built southern uphill Ghat Road. The geology of the area, studied using geomatics tools like Remote Sensing, SRTM based Digital Elevation Models, GPS Survey, etc., showed that Tirumala hills is under the grip of upward tectonic movement as evidenced from the N-S and E–W oriented Pleistocene faults, intensely dissected Plateau top Cuddapah Quartzites, retreating escarpments, exhaustive debris slopes, extensive valley fills along the slopes, colluvial fills in lower slopes, palaeo debris flows along the southern and western obsequent slopes of the Tirumala hills etc. All these indicate the inherent landslide vulnerability of the slopes. The E-W trending dykes which are piercing the slopes and standing as ridges add further landslide vulnerability to such fragile slopes. So, the new ghat road laid along such southern slope is obviously facing landslides. However, the detailed geomatics based studies show that the dykes, valley fills and steep slopes are particularly more vulnerable to landslides. Though remedial measures have been broadly evolved, abandoning the southern uphill new ghat road and widening the older northern downhill ghat road seems to be the better and long term feasible alternative to prevent Landslides.

HOUSING OF LABORATORY ANIMALS

Objectives

The important criteria to be kept in mind for the construction of animal house are:

• Got to satisfy the requirements of animal care takers and animal technician whose place of work it is.
• Got to satisfy animals which are house in animal house.
• Research workers who conduct research on animal in the laboratory should be satisfied.

Materials required- Small animal house, Animal colonies, type of cages and equipments.

Weeds can be considered a significant problem because they tend to decrease crop yields by increasing competition for water, sunlight and nutrients while serving as host plants for pests and diseases. Since the invention of herbicides, farmers have used these chemicals to eradicate weeds from their fields. Using herbicides not only increased crop yields but also reduced the labor required to remove weeds. Today, some farmers have a renewed interest in organic methods of managing weeds since the widespread use of agro-chemicals has resulted in purported environment and health problems. It has also been found that in some cases herbicides use can cause some weed species to dominate fields because the weeds develop resistance to herbicides. In addition, some herbicides are capable of destroying weeds that are harmless to crops, resulting in a potential decrease in biodiversity on farmers. It is important to understand that under an organic system of weed control, weeds could never be eliminated but only managed. In organic agriculture weeds are the resources as they are mostly native to the field/areas of existence (Children’s of the soil)

GENERAL CHARACTERISTICS OF FUNGI

1. Thallus

The body of the fungus is called as Thallus, which is without stem root and leaves. It maybe Plasmodial, Pseudoplasmodial , Pseudomycelial or Mycelial. A single thread like filament is called as hypha. A hypha is made up of a thin, transparent tabular wall filled or lined with a layer of protoplasm.

A group of hypha constituting the body of fungus is called as mycelium may be septate or aseptate. i.e coenocytic.

a) Coenocytic or Nonseptate or Aseptate Mycelium

When mycelium is not divided by cross walls called as Cornocytic mycelium.

Depending upon the nature of parasitism with the host plant, mycelium is either ecotophytic or endophytic.

b) Septate Mycelium

When mycelium is divided by cross walls or septa called as septate mycelium.

INTRODUCTION

The current food crisis has put the agriculture production on a tight leash, not allowing the producers any lassitude whatsoever. Even though we have outgrown from our ‘ship to mouth existence’; our least negligence can torpedo our efforts to maintain the steady state of progress achieved in food grain production. Around 35% of what is produced is lost due to pest and diseases. In this situation, plant protection assumes significance. Unfortunately our plant protection regime begins and ends with pesticides. It is the default option in the plant protection menu and all the other options more or less remain defunct and unused. Even though, our major thrust areas of plant protection are promotion of Integrated Pest Management: ensuring availability of safe and quality pesticides for sustaining food production from the ravages of pests and diseases, streamlining the quarantine measures for accelerating the introduction of new high yielding crop varieties, besides eliminating the chances of entry of exotic pests; we remain largely insulated from these aspects in IPM.

With the Globolization and liberalization in International trade of plants and plant material in the wake of Sanitary and Phytosanitory (SPS) Agreement under WTO, the plant quarantine measures have become more imperative. Liberalization of trade policies have helped the world agriculture trade to prosper which is key sector for many countries like India whose economies are dependent on agrarian industry. But the likehood of the presence of disease/pest inherent in the import material can very well geopardize the trade. Activities are meant to help agricultural development and Plant quarantine service are charged with the responsibility of preventing the entry of hazardous pests, pathogens and weeds, but to deny entry of valuable genetic re-sources would be against national interest. These activities are meant to help agricultural development and they are complementary to each other and therefore are necessary, and we on our parts need to be fairly vigilant. As has been very truly said-An ounce of prevention is worth a pound of cure.

1. Cattle
2. Buffaloes
3. Sheep
4. Goat
5. Swine
6. Camel
7. Rabbit
8. Poultry

Animal husbandry

Animal husbandry is the branch of science concerned with the care and breeding of domestic animals such as cattle, hogs, goat, sheep and horses.

India supports nearly 20% of the world livestock and 16.8% human population with a land area of only 2.3%. India leads in cattle and buffalo population and has world’s second largest goat and third largest sheep population. As per the 19^th Livestock census (2012) cattle (191 millions), buffalo (109 m), Sheep (65 m), goats (135 m), pigs (10.29m), camels (0.4 m) and poultry (729.2 m) population was reported in India. The total livestock population has decreased by about 3.33% over the previous census. India’s milk production increased from 43 million tonnes in 1983 to 155.5 million tonnes in 2015-16 (annual growth of 6.27%) and stands first in milk production in world.. The egg production is around 82.93 billion during 2015-16. The per capita availability is around 66 eggs per annum. The poultry meat production is estimated to be 3.26 million tonnes. Wool production (43.6 million Kgs) and meat production is 7.0 million tonnes in 2015-16.

Abstract

Seaweeds are the large marine algae that grow almost exclusively in the shallow waters at the edge of the oceans. Seaweeds are rich sources of many bioactive compounds and nutraceuticals. These factors are considered under two categories: Seaweed phytochemicals and Seaweed polysaccharides. They are rich in soluble dietary fibers, proteins, minerals, vitamins, antioxidants, phytochemicals, and polyunsaturated fatty acids, with low caloric value. The red, brown and green seaweeds have been shown to have therapeutic properties for health and disease management. Usually they are only used as gelling agent and stabilizers in the food and pharmaceutical industries, but current research has revealed their potential medicinal uses against many diseases like cancer, allergy, diabetes, oxidative stress, inflammation, thrombosis, obesity, hypertensive and other degenerative ailments. In line with other natural foods like fruits, vegetables and grains, there has been marked interest within the scientific community to assess which fractions of seaweeds may be linked to the historically observed health benefits. As consumer health and nutrition become more influential in the food industry, the use of seaweed as an ingredient is on the rise in product development. For several centuries there has been a traditional use of seaweeds as food in China, Japan and the Republic of Korea. This review undertakes successful exploration of potential of seaweed gums as an functional ingredient in a number of food applications. This addition has the potential to enhance the nutritional quality of a product and hence human health.

ABSTRACT

Leaf N and chlorophyll (Chl) concentration of crop are important indicators of plant nitrogen status. Laboratory determination of plant tissue N is time consuming and costly. Also remote sensing is quickly becoming recognized as a valuable tool that has the potential to asses a wide variety of physiological properties over a large area in a short amount of time. This study examined the relationship of sorghum and bajra canopy reflectance spectral response to its nitrogen and chlorophyll content. The study consisted of two nitrogen level (N₀ : no nitrogen and N₁: recommended dose of nitrogen for each crop) for two crops (sorghum and bajra) . Chlorophyll and N content were measured throughout the growing season for both crops. Reflectance at increased significantly as N fertilizer rate decreased. Chl and N were strongly related to canopy reflectance for either individual wavelength or for spectral vegetative indices or ratios. Sorghum nitrogen fertilizer rate mainly affected leaf reflectance at 575 and 623 nm, while bajra at 565 and 657nm. The reflectance values at 581 and 603 nm had the highest correlation with sorghum leaf N concentration. Similarly, bajra leaf N concentration was highly correlated with 619 and 696 nm. Sorghum and bajra leaf N concentrations were highly correlated with reflectance ratio of R₅₈₁/ R₃₈₁ (r²= 0.44*) and R₆₁₉/R₄₆₂ (r²= 0.78***) respectively with greatest r² value. Similarly, Sorghum and bajra leaf Chl concentrations were highly correlated with R677/R527 (r²= 0.63**) andR688/R409 (r²= 0.71***) or R615/R411 (r2=0.71***),

respectively. Thus our results suggest that spectral reflectance measurements hold promise for the assessment of some physiological parameter at the leaf level real time monitoring of sorghum and bajra N status and N fertilizer management.

There are several types of features and structures of the gardens. The design, material and placement varies from one type of garden to others. However, there are some basic requirements in every type of gardens. Common features and structures of the gardens are described hereunder for providing some basic information.

Boundary

Material and construction of the outer boundary is to be considered depending upon the size and type of garden. Protection, permanency and cost of construction are the main factors. It should be well designed and an architectural show piece co-relating with type and design of the garden. Ornamental creepers are planted along the boundary wall and trained over the same for further beautification purpose.

Rose is most popular of all garden plants and regarded as queen of the flowers. Various colours, forms, fragrance of the flowers are major attraction. Roses are generally grown as bedded plants but can successfully be grown in pots also. Therefore, those who do not have land for bedding purpose may grow them in pots. Every kind of garden has scope for growing roses in various forms. In home garden, growing roses is always preferred. A single bloom of rose creates a tremendous sensation and enjoyment to the house owner. Similarly, public parks, institutional, factory and temple gardens have equal scope for growing roses in beds. There are large numbers of cultivars available in the horticultural trade and one has to select them depending upon the garden type, climatic conditions and purpose of the garden.

Species and Cultivars

Rose (Rosa sp.) is a woody perennial belongs to the family Rosaceae. There are about more than 100 species having varied growth habit ranging from erect shrub to climbing and miniature. Similarly, flowers have different forms, size, colour and fragrance. Majority of the species are native to India while a smaller number is native to Europe, North America and northwest Africa. Species found in India are - Rosa clinophylla (R. involucrata), R. foetida, R. gigantea (R. odorata var. Gigantea), R. leschenaultiana, R. moschata, R.macrophylla etc.

For development of garden roses, following eight species had main contribution as parental species - Rosa chinensis, R. damascena, R. foetida, R. gallica, R. gigantea, R. moschata, R. multiflora and R. wichuraiana. Inter-species crosses between Chinese roses and European started the development of modern roses.

Bonsai is the art and science of dwarfing plants and growing them in shallow containers. The word ‘Bonsai’ is a Japanese term consisting of two words, ‘Bon‘- a shallow container and ‘sai’ - to plant. Therefore, bonsai is a technique of growing plants (trees, shrubs and others) in shallow containers in dwarf form. With the help of pruning, pinching and training a three dimensional effect is produced. It is a kind of living sculpture and idealized nature in miniature. An ideal bonsai is replica of a particular plant or an artistic variation in shape whose different parts are in complete harmony. Development of bonsai requires an artistic eye, skills on training, pruning and knowledge on growing plants in containers.

This technique was developed by the Chinese over 2000 years ago and later excelled by the Japanese. Bonsai is now popular all over the world and very useful for the people who are living in flats and have no scope to have outdoor gardens. Every house owner likes to have few specimen plants for interior decoration. Bonsai provides them an additional opportunity to grow more number of plants being dwarf in nature. Considering its present popularity, Bonsai is now important horticulturally for its commercial and aesthetic value.

Floral decoration in India has got a historical background spreading over different eras. Admiration of natural beauty, plants and flowers were part of civilization process. Many evidences are there in the paintings, carvings on wall of caves, temples, mosque besides literatural references that flowers were in use in many forms since time immemorial. Every religion, culture, rulers and regimes had great influence on the use of flowers.

At present, flowers are integral part of our daily life. We use flowers in various ways and for many purposes. Loose flowers are used for worship while garlands for decoration purpose during social, institutional, official functions etc. In addition, cutflowers in the form of bouquets are very common in use. Arrangement of flowers in the vase, bowl or any other container is displayed extensively for interior decoration. At present, placing flower vase is very popular in houses, corporate offices, institutes, hotels etc. and is a well established practice.

Manychemicalreactions innature,particularlyinlivingsystems,occur inaqueous solutions. Reactions are often carried out in the laboratory in aqueoussolution becausethese aregenerallymore rapid in solutionthanwhen puresolid reactions are mixed. Analysisof substancesmaybe qualitative or quantitative in nature. A quantitative analysisis one inwhich the amountor concentrationof a particular species in a sample is determined accurately and precisely.

1.1 Volumetric Analysis

Volumetric analysis is a quantitative analysis. It involves the measurement of the volume of a known solution required to bring about the completion of the reaction witha measuredvolume of the unknown solution.

The reaction used in volumetric analysis must fulfil the followingconditions;

14.1 Principles of X-ray Diffraction

Any crystalline structure is characterized by a regular and systematic arrangement of atoms (or ions) in a three-dimensional array. Since crystals are composed of regularly spaced atoms or ions, each crystal contains planes of atoms or ions separated by a constant distance which is the characteristic of that crystalline species.

X-rays are essentially electrostatic and electromagnetic fields oscillating in planes perpendicular to each other and to the direction of propagation in periodic cycles. X-rays having wavelengths in the order of 10^-3 to 10¹ nm, are produced within a vacuum x-ray tube by bombardment of a metal anode with high-velocity electrons. High-velocity electrons transfer their energy to the electrons of metal anode causing their elevation to higher energy level (excited state). Excited electrons of metal atom soon come back to the vacant shell and each electron transfer from higher to lower energy state results release of a quantum of energy (x-ray photon) equivalent to the difference in energy between these two levels. The energy and the wavelength of emitted x-ray photons are finite and characteristic of the particular atoms of the metal anode used in x-ray tube. Usually, photons generated due to electron transfer from L-shell to K-shell are used for x-ray diffraction analysis.

Diffraction of x-ray involves scattering of x-rays by planes of atoms of the crystal separated by definite distance and reinforcement of scattered rays in definite direction away from the crystal. Reinforcement of scattered rays is quantitatively related to the distance of atomic planes in a crystal as defined by Bragg’s equation:

18.1 Determination of Electrical Conductivity of Soil Solution

The conductivity or more precisely the specific conductance of a soil at a given soil-water ratio is the reciprocal of the specific resistance offered by the solution at 25ºC between the electrodes of 1 sq cm cross section kept 1 cm apart. Thus, the electrical conductivity of any solution depends on the amount of soluble salt present in it. Knowledge on the extent of salinity is important for management of saline soil including the choice of the crop suitable for that soil. Soluble salt content in saturation extract is more reliable index of salinity level than in soil: water ratio of 1: 2 or 1: 2.5, because it simulates the extent of salinity experienced by crop in field moisture condition.

Salinity class of soil is based on the electrical conductivity (EC) of saturation extract at 25ºC. However, EC of water extract from 1:2 soil-water suspension can be transformed into the EC of saturation extract following the formula (except for soil containing gypsum).