eChapters

Biofertilizers are one of the important components of organic farming and sustainable agriculture. Awareness among farmers is increasing on the biological fertilizers. But, the success of biofertilizer inoculation depends on the quality of the inoculant used. Because farmers are unable to judge the quality of the inoculants at the time of purchase or even at use. The inoculant producers are negligent to institute quality control programmes. Unfortunately much of the inoculant produced in the world today is relatively of poor quality. In such situation maintaining high quality inoculant products depend on the internal implementation of effective quality control systems by manufacturer. A major goal of a quality standard is to control the quality of inoculant to be used in any country.

Robots can replace human efforts in the future. Discovery of robots in agriculture is going to accelerate the growth of agriculture 4.0. Nursery planting needs robust and profitable solutions. Nursery plants deals with the direct consumer, which is the primary stage of agriculture. An intensive care is required to look after the nursery plant before going to be planted. Now a days robots are used to monitor the plants, essentially to maintain the health standard of a plant. This chapter illustrate the applications of the robots in nursery planting.

6.1 Introduction

Nursery is the primary stage where seeds are grown in to the young plants. Nursery planting involves many activities like seeding, potting and monitoring. The process required high attention to look after at this stage [1]. As the food demand is increasing day by day, it is necessary to adapt unconventional way of farming. Bringing robots in to the farming will bring a lot of changes in the traditional agriculture. The robotics in agriculture is not new, it has started with evolution of autonomous vehicles [2]. The usage of robots are increasing exponentially. So the researcher and scientist also started use of robots in agriculture. They found a phenomenal result in term of easy to handle the agro tasks, seeding, weeding, automatic irrigation and harvesting. It draws the farmer attention down the line [3].

Agriculture is the backbone of India. Evolution in technology is bringing new dimensions of conventional agriculture. Looking towards the current food demands it is very crucial to maintain the food supply. According to UN (United Nations), by 2050 the world population will be increased to around 9.3 billion which increases the food need. As the technology in agriculture evolving it seems that we could be able transform conventional farming to unconventional and traditional to modernization by the help of agriculture robots. Agri-bots can be autonomous with human intervention that could perform the task precisely. Chapter illustrates the applications in agriculture seeding. These robots are efficiently used in crop seeding.

7.1 Introduction

The very first agriculture robots were used in the early 1920s along with autonomous vehicle development.

Agro robots are becoming an ongoing pattern in farming with lots of research advancement and business models [1]. Agrarian robots have huge focal points as far as adaptability, flexibility and ecological advantages contrasted with customary horticultural apparatus and speak to an extraordinary resource for cutting edge precision agribusiness. Numerous advances in machine vision with imaging and otherworldly cam-periods for distinguishing weeds, vermin and infections, supplement inadequacies in soil or plant leaves have given profound applications to be mounted on independent vehicles for exploring soil and crops and for additional downstream choice help and control [2]. The mechanical network has additionally made earth shattering upgrades and advancements as far as utilizing a far reaching working framework, the Robotic Operating System (ROS), just as applying strong stages and route calculations.

Comparable to horticultural robots, the attributes of the central framework of robots are the lightweight, little size and lively self-governance [3]. Lightweight implies that the vehicle requires lower impetus vitality and incites less soil compaction while simultaneously the vehicle must be little for security reasons, for accomplishing more noteworthy accuracy during execution of assignments and having more maneuverability inside the field to limit turning delays.

Precision Agriculture is fulfilled by adapting suitable monitoring and analysis mechanisms. Autonomous monitoring is getting a new dimension using robots. Agriculture is the trending area to attract new professionals, investors and new companies. The technology in agriculture is not only increasing the yields but the time and labour. This chapter illustrates the use of robotics in crop monitoring and analysis.

8.1 Introduction

Monitoring of agriculture farm enhance the productivity. Evolution in technologies in the era of agriculture brought a lot of innovations. Among these innovations robots are one of them to be implemented in agriculture to enhance profitability and reliability with minimum human resource. At the same robots were deployed to monitor the farming land from weeds and try to remove these. Due to which uses of agrochemicals reduced down the time line. When precision farming came in to the pictures robots are the best use cases. In fig. 8.1 autonomous mechanical robots are shown, which are used to remove the weed from farming land. Robots are equipped with sensor modules, actuators and IoT enabled which makes the things very easy to control from remote area with commands.

Agriculture irrigation is a crucial part of precision farming. An irrigation system required a lot concentration to grow the plant healthy. A smart irrigation system in an agriculture farm leads to maximum profits in terms of yield. Integrating technologies like IoT (Internet of Things), AI (Artificial Intelligence) in irrigation accomplish to the human efforts. Controlling of water pumps, sprinklers seamlessly draws the kind attention of farmer to adapt these technologies in their day today farming schedules. This chapter illustrates a wide variety of robots used in irrigation to achieve maximum yield and minimizing water loss. The high scalability and reliabilities of these autonomous robots replicates the potential of agriculture 4.0 in coming future. Advanced robots deployed on the field to monitor the land and pass the information to the controllers and further to the water pumps. Here case study of robots is highlighted to reduce water losses by using nozzles mechanisms.

9.1 Introduction

Agriculture faces many environmental challenges. As far as the irrigation in agriculture is concerned it is very essential to maintain soil hydrated and water level in the field. Robotic irrigation enables autonomous irrigation from remote access [3]. Smart irrigation technique enables a lot of water saving. So robotic in agriculture plays a very crucial role in it [2]. In order to avoid water losses agro robots adapt smart irrigation techniques like droplet irrigation and sprinkling. To maintain sustainability, water resource management is required. Technologies like drones, smart sprinkler based on IoT, smart droplet irrigation used across the globe. These technologies have the greatest impact on productivity and sustainability of the environment as well. As far as the country India is concerned, due to diversity in geographical infrastructures rainfall changes from state to states. So, a wide range of water diversity is found to grow agricultural foods. For example northeast and southern part of India due to heavy rainfall paddy cultivation is preferred since it requires a lot of water. Whereas the northern part of India observe a moderate rainfall, so vegetables and other agriculture foods get cultivated. At the same there are certain states like Rajsthan, Gujrat where very less rainfall occurs through varieties of crops related to dal.

In the wild (forests) plants grow by their own, but in agriculture because of limited space they don’t have freedom to grow in a much natural way. This can lead to structural irregularities in their growth, and can hamper the overall plant’s development and this will impact the produce or crop yield. To deal with such constraints and to boost the crop production, the methods of thinning and pruning provide efficient ways to train the growth of young plants and maintain the health of grown-up plants.

11.1 Introduction

In agriculture, thinning means the removal of some plants or some parts of plants that show inconsistent growth and or are damaged by some pest or disease, without removing the whole tree or plant. The selective removal of branches, buds or roots is termed as pruning [1]. If the plants are overcrowded in a confined space, the overall health of the crop decreases due to the competitive stress from the neighbouring plants. Thinning and pruning is done to improve the growth rate or health of the plants by decreasing the competitive stress. Thinning and pruning in agriculture is the sensible removal of plant parts such as flowers, shoots, its branches or other parts to correct or maintain that structure of the tree and control be directed growth of the crop. This practice covers the precise removal of the unhealthy and obstructive part of the plant branch, leaves, fruits, buds, fruits, etc. Pruning improves the quality and longevity of the crop, leading to quality produce and increased yield of the field. This also helps in increasing the size of the fruit as it increases the availability of nitrogen required for growing and stimulating growth of the crop. There are several factors that influence the amount of pruning to be done, i.e., age of the plant, condition of the bark and wood, growth characteristics, whether cup crop/plantation is permanent or seasonal [2]. Pruning is done for controlling the size of the plant, controlling the structure makeup of the plant, controlling and improving the light distribution of the plants by the selective removal of leaves to improve the quality of the fruits, removing the diseased parts of the plant and to regulate the fruit crop and increase the life of the tree.

In the wild (forests) plants grow by their own, but in agriculture because of limited space they don’t have freedom to grow in a much natural way. This can lead to structural irregularities in their growth, and can hamper the overall plant’s development and this will impact the produce or crop yield. To deal with such constraints and to boost the crop production, the methods of thinning and pruning provide efficient ways to train the growth of young plants and maintain the health of grown-up plants.

11.1 Introduction

In agriculture, thinning means the removal of some plants or some parts of plants that show inconsistent growth and or are damaged by some pest or disease, without removing the whole tree or plant. The selective removal of branches, buds or roots is termed as pruning [1]. If the plants are overcrowded in a confined space, the overall health of the crop decreases due to the competitive stress from the neighbouring plants. Thinning and pruning is done to improve the growth rate or health of the plants by decreasing the competitive stress. Thinning and pruning in agriculture is the sensible removal of plant parts such as flowers, shoots, its branches or other parts to correct or maintain that structure of the tree and control be directed growth of the crop. This practice covers the precise removal of the unhealthy and obstructive part of the plant branch, leaves, fruits, buds, fruits, etc. Pruning improves the quality and longevity of the crop, leading to quality produce and increased yield of the field. This also helps in increasing the size of the fruit as it increases the availability of nitrogen required for growing and stimulating growth of the crop. There are several factors that influence the amount of pruning to be done, i.e., age of the plant, condition of the bark and wood, growth characteristics, whether cup crop/plantation is permanent or seasonal [2]. Pruning is done for controlling the size of the plant, controlling the structure makeup of the plant, controlling and improving the light distribution of the plants by the selective removal of leaves to improve the quality of the fruits, removing the diseased parts of the plant and to regulate the fruit crop and increase the life of the tree.

The principle behind thinning and pruning is to admit more sunlight to the branches that bear fruit by the selective removal of the unproductive branches which obstruct the sunlight to fall on the productive branches to increase the productivity white and vitality of the plant to obtain optimum healed of good quality crop [3]. Young trees are pruned so that they acquire the desired shape. In old trees it is done to stimulate flowering. In plants bearing fruits or crops, pruning is done to allow adequate sunlight to fall on fruit bearing branches, so that quality crop is produced. Very old plants heavy pruning is done to restore the vigour of the plant. It is also done so that the loss of nutrients being shared by the diseased peak or shading branches is reduced. The use of robotics and other automated systems can aid in the precise pruning and thinning of the crop. This will also automate the whole process and will save their requirement on the extensive manpower which ultimately saves time.

To cater the increased demand of food, it will be required that farmers are equipped with tools and methods to improve their yields and make informed decisions [1]. Also, with the increase in population, the agricultural land is decreasing by 1 lakh hectares per year and it is required to double the agricultural produce in the next 30 years to sustain the global food requirements.

The improvements in various technological fields like machine learning, navigation, robotics etc. and their applications in agriculture is required to meet this increasing need. One of the factors is to make the farmland ready for sowing the crops, spraying, etc. and this has to be done in a precise and faster manner to address the latter issues. So, the uses of autonomous tractors for such jobs offer accurate, precise and timely preparation of the fields for the cultivation.

12.1 Introduction

Autonomous tractors or driverless tractors are unmanned ground vehicles mainly employed in agriculture for various purpose like preparation of land for the crops, harvesting, spraying, and other agricultural purposes. They are equipped with GPS, autopilot, cameras, lasers (LiDAR), and other wireless technologies navigation and mutual coordination and offer saving of both the manpower and time. These autonomous tractors can be programmed to navigate their paths through the fields and are designed to avoid the obstacles while doing their jobs. These tractors automate various laborious field jobs and also minimize human intervention in the process.

These autonomous machines are regarded to revolutionize the agriculture industry and offer safety, sharing of resources, economical solutions per square area of land, etc. Several industries like Jhon Dheere, AgraBots, EcoRobotix, RowBot, etc.

Harvesting is one of the most labour intensive jobs in agriculture, and by implying the robotics in harvesting, the quantity of the harvested yield can be readily increased, thus saving a lot of time and human resources. This also aids in reducing the farm to market transportation times. The use of robotics can also reduce the seasonal requirement of the manual labour and thus reduce the recurring costs.

13.1 Introduction

The incorporation of robotics in agriculture has proved to be advantages for the farmers and thus for the economy. The automation of various agricultural processes led to the reduction of the operational costs and also in the reduction of the labour required. A possible solution to address the problems of labour availability and scaling up the harvesting of the crop is the incorporation of robotics.

The development of the civilisation humans have tried to domesticate the animals. Initially dogs were known to be the first pet domesticated by humans followed by the domestication of other animals like cattle, horses, sheep etc.

14.1 Introduction

When humans started to domesticate the animal, they have tried several ways to control them. Generally these animals are released in free space to graze and one of the known problems is to prevent them from overgrazing. So building a fence is one of the ways to limit their movement is one viable solution, but building a fence is limited to a smaller area. Since these animals are locked in a large number, so building a bigger fence and moving it every time for grazing is not viable. It can be observed in the history of humankind as that civilisation progressed the use of Shepherd dogs has been one of the widely accepted. Shepherd dogs not only help in shepherding and herding but also prevents these livestock from wolves

The incorporation of robotics will not only automate the process intelligently but also keep a vigil on various aspects of livestock management. In recent years there has been a substantial development in this regard. The development of robotic dogs for shepherding and herding purposes has found a lot of increment developments. SPOT developed by Boston dynamics and SwagBot developed by University of Sydney, are well-known robots developed in recent times for the purpose.

These robots are equipped with multiple sensors like LiDAR, gas and heat sensors, high-resolution cameras etc. The array of sensors are used to capture the data in real-time and is then used for decision-making processes. Also these reports are built to be rugged and can navigate on a variety of terrains.

Cape gooseberry is the native of Peru and Chili (South America), but widely cultivated in Cape of Good Hope and hence called so. It is known by different name in various parts of the world. It is commonly called ‘Poha’ in Hawaii; ‘Golden berry’,’ Pompelmoes’ or ‘Apelliefie’ in South Africa; ‘Lobolobophan’ in the Philippines. In India it is commonly called ‘Rasbhari’, ‘Makoi’, ‘Tiparee’ or ‘Tepari’. Cape goose berry (Physalise peruviana L.) belongs to the family solanaceae. Out of 80 species of genus physalis, only three are well known for their fruit value. These are: (i) P. pubescen L. (ii) P. Peruviana L., and (iii) P. ixocarpa Brot. However these three species, Physalise peruviana L is the most popular due to its pleasant flavour and acid-sweet taste.

The paddy grain contains a rough outer covering called husk. It accounts for about one-fifth to one - fourth of the weight of paddy. The inner kernel, called brown rice or dehusked rice, again contains some soft outer layers, jointly called bran. It accounts for about 6-8% of the brown rice weight, including the small germ (1-2% by weight) located in one corner. Rice milling is the process of removing the husk and a part of the bran from paddy in order to produce edible rice. Rice milling system ranges from the home-scale to the large, complex modern rice-processing installations. They include hand-pounding equipment, single hullers, emery sheller-cum-huller mills, emery sheller-cum-cone polisher mills and the modern rubber – roller rice mills. Rice milling industry does not only mill rice but it also carries many other essential functions, such as cleaning and grading, drying, storage, quality control etc. for the production of better quality rice. All these processes are discussed in this paper.

Unlike other food grains, rice is mostly consumed as cooked whole grain, Milling technology is therefore geared to obtain maximum outturn of milled rice and to reduce breakage to the minimum. The single huller mills are by and large located in villages or in localities where paddy is custom milled for produces and they still handle the bulk of the country’s production. The large-capacity rice mills located in urban or semi-urban areas for commercial milling are of ½ to 4 tones per hour capacity and handle the rest of the paddy milled. Some battery hullers are still in operation as large commercial mills, specially for milling parboiled paddy.

Human societies over the ages have depleted natural resources in different ways and degraded their local environments. Indiscriminate cutting down of trees and accelerating the construction works lead to global warming and climate change. Climate scientists believe that human-induced deforestation is responsible for 18-25% of climate change. Accumulation of greenhouse gases in the lower atmosphere is the main cause of global climate change. The concentration of these gases in the earth’s atmosphere is increasing, mainly due to deforestation and the combustion of fossil fuels which release carbon dioxide.

The earth receives heat energy constantly from the sun through radiation. Some of the heat is absorbed and some is reflected. Carbon dioxide works like an invisible blanket that wraps around the earth and traps the heat inside, similar to the function of a greenhouse. A greenhouse is a structure that is used in colder climates to grow plants. Even when outside temperatures drop below freezing point, greenhouses are still warm enough inside to grow plants. Greenhouses are made of glass, which allows solar radiation to enter. The heat is trapped inside the greenhouse, allowing plants to grow all the year round. Increasing concentrations of carbon dioxide in the earth’s atmosphere insulate it like a greenhouse, leading to a gradual warming of the earth’s atmosphere. Carbon dioxide is the major greenhouse gas, but there are others as well, including methane and nitrous oxide.

Mitigation means addressing the causes of climate change, while adaptation attempts to tackle its effects. The Intergovernmental Panel on Climate Change defines mitigation as an anthropogenic intervention to reduce the sources or enhance the sinks of greenhouse gases and adaptation as the adjustment in natural or human systems to a new or changing environment (IPCC, 2007).

In 1907, the Russian Nobel laureate, Dr. Elie Metchnikoff, fascinated by the unusual longevity of Bulgarian farmers, consuming beneficial lactic acid bacteria by way of traditional fermented milk products, suggested that regular intake of friendly microbes could benefit human health. Although Dr. Metchnikoff ’s recommended bacteria for the purpose proved largely ineffective, the theory was carried forward with moderate success until the war on bacteria began because of the advent of sulfa drugs and antibiotics (Scott, 2012). However soon after their rampant use and the realization of the rapid spread of antimicrobial resistance, researchers turned yet again to ecological notions and the time was fertile for the advent of probiotics. By the 1980’s the term had stabilized both in medical and veterinary literature. The mid 1990’s witnessed a surge of exponential studies on probiotics, the definition of Probiotics emerged in 2001 and the years thereafter saw tremendous progress in the science of probiotics.

Almost simultaneous was the study on the study of the intestinal microbiota when Alfred Nissile demonstrated that transferring members of the human gut microbiota to healthy typhoid carriers helped in Salmonella being cleansed from their system (Nissle, 1916). It was then, that the importance of the gut microbes in prevention of infection became evident. What followed was the advent of culture independent, modern biotechnological tools for whole genome sequencing and the successful launch of two most ambitious projects - Human Microbiome project (Turnbaugh et al., 2007) and the Met Hit project (Metahit, 2009; Qin et al., 2010). They provided fascinating insights into the highly complex microbial ecosystem harboured by the human body. The term Microbiome (refers to the collective genome of our microbial inhabitants) had entered literature in 2001 and the concept of gut microbiota in maintaining overall health gained wider attention.

Tannins: Group of plant phenolic compounds found in higher plants as secondary metabolites. Their main function is to defense against microorganisms, insects, and herbivores and in allelopathy.

Taxis (tactic orientation; formerly topotaxis): Movement of motile organisms, cells or organelles, the prevailing direction of which is determined by the direction of the stimulus.

TATA box (Hogness box): A sequence of nucleotides which serves as the main recognition site for the attachment of RNA polymerase in the promoter region of eukaryotic genes. Located at around 25 nucleotides upstream of the transcriptional start site. It consists of seven base consensus sequence, TATAAAA.

TCA cycle: Tricarboxylic acid cycle. It is also called as citric acid cycle or Krebs cycle, It is a step in aerobic degradation of glucose to convert into energy. During this cycle several intermediates are produced, which leads to several metabolic pathways. During this cycle, there is production of reductancts such as NADH, FADH and GTP.

Telomere: Sequences at both termini of each eukaryotic chromosome that facilitate replication.

Smooth gourd or sponge gourd (2n =2x = 26, Luffa cylindrica Roem syn. aegyptiaca, family Cucurbitaceae, monoecious, cross-pollinated but genetically behaving like self-pollinated crop) is not a global crop and is a vegetable crop very much indigenous to India and the adjoining countries. As per estimates, the acreage of this crop in India is about 50,000 ha spread over almost all the states but on a limited scale. However, UP, Bihar and West Bengal are the main states growing sponge gourd.

Origin and Domestication

It is agreed that sponge gourd may have originated from Asian sub-tropical areas, particularly India and India itself should be the centre of domestication as well because global presence of this crop is negligible (Kalloo, 1993). NBPGR, New Delhi publications unanimously mention Indo-Chinese and Hindustani gene centres as primary centres/domestication/secondary centres for Luffa species and in their publications, Luffa aegyptiaca is more commonly used than Luffa cylindrica for sponge gourd (Pandey et al., 2019).

Benefit of biofertilizers have been extensively studied for various agricultural and horticultural crops. However, the effectiveness of inoculated biofertilizers are influenced by several factors. If the use of biofertilizers have to be popularized in horticultural crops, the major factors affecting their performance particularly in relation to soil, plant, quality of the product and application methods have to be addressed. Factors affecting the performance of biofertilizers are:

4.1 Quality of the product

4.1.1 Production process

The high quality of biofertilizers are determined by the production process (Bashan et al., 2014). At the same time, the population density of mother culture and the quality of the final products are directly related (Stephens and Raskm, 2000). As the inoculum consists of a strain, the relationship among the microorganisms interaction in the rhizosphere have to be understood. In the case of more than one microorganisms, the efficiency depends on the various mode of action by various microorganisms which might overlap with antagonistic acitivities (Vassilev et al., 2001, 2006 b). The relationship of microorganisms with plants is not based on the taxonomic diversity, but their functional diversity (Maherali and Klironomos, 2007).

The efficiency of biofertilizers could be assured by enhanced shelf life of the inoculant and biological traits which are a challenge for developing a formulation (Bashan, et al., 2014). Hence, either single or consortia of microorganisms formulation with or without additives determines the efficacy of the biofertilizers. The formulation determines shelf-life during storage and transport, which enhances the persistence of the strain in soil and get maximum benefits to the host plants after inoculation (Manikandan et al., 2010; Schoebitz et al., 2012). Different kinds of carriers are used in the formulation process which affects the overall quality and efficacy of the biofertilizers (Bashan et al., 2014; Herrmann and Lesueur, 2013). Granular inoculants showed good results under stressed soil conditions (Clayton et al., 2004; Lupwayi et al., 2006). Encapsulation of the microbial strain into polymers allow diverse compositions and structures (Vassilev et al., 2005) but, have limitations for commercial production (Bashan, et al., 2014; John et al., 2011). Use of additives might improve the shelf life of the product (Bashan et al., 2014; Malusà et al., 2012; Herrmann and Lesueur, 2013) with introduction of specific substances to enhance the efficacy of biofertilizers.

Biofertilizers can directly or indirectly influence the growth of plant. The direct influence can be through production of phytohormones or making the nutrients available to plants. The indirect effect can be through management of plant pathogens through biological control. Therefore, the purposeful introduction of biofertilizer inoculants to plant microbiome represents an environmentally sound option that holds a prominent position in order to reduce the dependency on agrochemicals (Adesemoye and Kloepper, 2009; Abhilash et al., 2016; Aloo, et al., 2019).

Microbes in soil can rarely exists as single cells and survive near the plant root canopy or in bulk soils or endophytes or even on plant surfaces (Lorito, 2006). The soil microflora occurs as complex members of microbiota (Hacquard, 2015). Microbial consortia (MC) are unique mixture of organisms which respond to the environment stress and adapt to stresses due to internal beneficial interactions among the microbial community. Ecosystem’s physiological functions by microflora is carried out by more than one microbial species with the functional diversity and succession among different microbial components. The microbial balance among the different microflora of a MC will consist of a continuous shift between actively growing cells and non-dividing cells of the microbial consortia. It has been reported that different microbial populations “talk” to each other by “quorum sensing” mechanism in a given environment by exchanging specific chemical signals (Thompson, 2015). Natural microbial consortia holds many specific properties like stability, functional diversity and perform complex functions. The natural consortia have generated an interest in manpulating synthetic consortia for the benefit of application (Minty, et al., 2013).

The biofertilizer technology has paved way for the manufacturers and entrepreuners to establish a biofertilizer production unit due to an increasing demand and awareness among farmers. Biofertilizer production units have already been started with most of them in the southern states of India. The biofertilizers can be produced using different kinds of carrier materials (peat, coal, lignite, clays, inorganic soil), organic materials (composts, soybean meal, wheat bran, sawdust, etc.), or inert materials (e.g., vermiculite, perlite, kaolin, bentonite, silicates). Natural carriers like peat, plant waste materials, composts, sawdust, sludge lignite, clays, coal, vermiculite, perlite and bentonite and mixture of organic and inorganic materials may also be used.

The Government of India is also encouraging a low cost technology by providing a subsidy to establish a biofertilizer production unit . The major equipment’s and other materials required for a biofertilizer production unit with the capacity of 150 metric tonnes/annum are given below

10.1 Application Efficiency and Irrigation Uniformity

All irrigation systems have some non-uniformity. This non-uniformity influences yields and irrigation efficiency especially application efficiency. If the net amount of water applied during irrigation is the same as that required to fill the soil water deficit, then because the distribution of water is never perfect, half of the field will receive too much water while the other half will receive too less water. In such a context, a farmer will try to apply more irrigation water to his field so that a larger fraction of the field has an adequate amount. This will tend to have higher percolation and runoff and thereby declining the application efficiency. An alternative to adding extra water is to improve the uniformity of water application. A major advantage when the uniformity is improved is that the amount of deficit in the area under irrigation is reduced and the potential for water logging and salinization is also reduced.

11.1 Performance of Farm Irrigation Systems

The performance of farm irrigation systems is determined by the efficiency with which water is delivered to the field and utilized to the fullest amount possible with minimum losses due to seepage and percolation, runoff, evaporation and other operational losses. The efficiency of the irrigation system will increase if the conveyance losses, application losses and other losses are reduced to a great extent.

11.1.1 Overall Efficiency

The overall efficiency of a farm irrigation system is defined as the percent of water applied to the farm that is used for irrigation on the farm. Irrigation efficiency otherwise called as overall system efficiency is defined.

India is bestowed with an enormous wealth of medicinal plants and has a rich heritage of treating human and animal ailments by using herbal medicines. However, there is need for a systemic, scientific approach to validate the authenticity of claims on plant-based medicaments. This approach has paid rich dividends in developing cheaper, safer, effective and eco-friendly remedies, which recently has gained worldwide attention. Cissus quadrangularis, Linn (Syn. Vitis quadrangularis, Wall; Heliotropium indicum, Linn) is a tender climber with fleshy quadrangular stems and grows in the hotter parts of Indian subcontinent, Sri Lanka and East Africa. In Hindi it is known as hardjore; in English as adamant creeper, bonesetter; in Ceylon as hiressa; in China as di xanh voung; in Burma as shazam-lese and in Bangladesh as harbhanga. Considering the advantage of herbal medicines, it is planned in this chapter to investigate the efficacy of Cissus quadrangularis, Linn, in one of the most commonly encountered problem of fractures in small animals.

Dried ethanolic extract of Cissus quadrangularis (CQ) is obtained from 500g of dried finely powered stems using soxhlet apparatus. It is dissolved in a vanishing base to make a semi-solid paste for local application. For parental use, this extract is reconstituted with distilled water (100 mg/ml) and filtered.

Twelve clinically healthy mongrel adult dogs aged 2-3 years and weighing 10-15 kg is randomly divided into two equal groups (A and B). In all animals operative site is prepared for aseptic surgery. Premedication is done with atropine sulphate @ 0.06 mg/ kg body weight subcutaneously and anaesthesia is achieved with a combination of Xylazine hydrochloride @ 1 mg/kg body wt. and Ketamine hydrochloride @ 10 mg/kg body wt. intravenously. Unilateral comminuted diaphyseal femoral osteotomy is created under general anaesthesia and the bone defect is immobilized with neutralization bone plating (AO/ASIF technique). All the animals are administered 5 mg/kg b wt Enrofloxacin intramuscularly for 5 d and 1 mg/ kg b wt Diclofenac sodium injection intramuscularly for 5 d postoperatively. Skin sutures are removed after 10 days. In the animals of group B, in addition to the postoperative treatment, the ethanolic extract of the herb, Cissus quadrangularis is applied on the skin twice daily along with subcutaneous injection (50 mg/ kg body wt.) on every alternate day for 20 d postoperatively.

Bone healing can be modified by variety of endogenous or exogenous factors that affect the metabolic function of bone cells. The Food and Drug Administration is approved the use of low-intensity ultrasound for the accelerated healing of fresh fractures in October 1994 and for the treatment of established nonunion in February 2002. The first regulatory approval is based primarily upon two rigorous, double - blind, placebo controlled clinical trials, which shows that the rate of healing of fresh fracture is accelerated by treatment with ultrasound. Therapeutic ultrasound has been able to improve functional activity, reduce post-ambulatory period, alleviate suffering and restore the animal’s health early. It has been used frequently for acceleration of healing in various musculotendinous injuries in animal. However, the role of ultrasound therapy in different dose levels in fracture healing has not been elucidated properly. In view of the above fact, this chapter is undertaken to investigate the effects of therapeutic ultrasound in two different doses, on cortical bone healing in rabbits.

Twelve clinically healthy adult New Zealand white rabbits of either sex are divided equally into three groups A, B and C, and kept on standard diet and uniform management. In all animals, mid-shaft simple transverse fracture is created in both the ulnae under thiopental (2.5%) anaesthesia. All the animals are administered broad-spectrum antibiotic and analgesic and surgical wounds are dressed daily with povidone iodine and antibiotic cream for 4 days postoperatively. Group A animal is received pulsed ultrasound therapy @ lW/ cm² (1:1) whereas, group C animals is received continuous ultrasound therapy @ 3 W/cm², starting on day 4 after the creation of fracture. Ten treatments, each consisting of 5 min duration, are given on alternate days. Group B animals are served as control. In both the test groups (A and C), the transducer head of the ultrasound machine is moved in a linear fashion along the length of the bone after applying ultrasound gel.

Among the epiphyseal and metaphyseal fractures of the different long bones, fractures of the proximal tibia are quite commonly reported and require special attention due to their proximity to the compound stifle joint. Hence, a standard fixation technique is needed to treat such fractures, which also permit early ambulation and preserve range of joint motion in addition to providing rigid fracture fixation. Different treatment modalities have been tried for fixation of metaphyseal fractures with variable results. No single method is appropriate in all circumstances and treatment indication often overlaps. Therefore, in this present chapter, an attempt has been made to evolve a standard technique for the management of such fractures.

Ten clinically healthy mongrel dogs are maintained under uniform housing, feeding and management conditions, acclimatized, immunized against rabies, dewormed and randomly divided into two groups (A and B) of five animals each. In all the animals unilateral metaphyseal fracture is created in the proximal tibia under general anaesthesia with intravenous thiopental sodium (5%). In the animals of group A, the fracture is immobilized with cross intramedullary Steinmann pinning with interfragmentary wiring, whereas, single intramedullary pinning along with interfragmentary wiring is performed in the animals of group B. Antiseptic dressing of the wounds is done daily for 1 week with povidone-iodine. All the animals are administered Enrofloxacin at the dose rate of 5 mg/ kg b.wt intramuscularly daily for 5 days posoperatively. Skin sutures are removed on day 10 post-operation

Edmond Nocard (French veterinarian) first isolated filamentous aerobic bacteria from clinical cases of ‘bovine farcy’ in 1888. In 1889, the genus Nocardia was formed by Trevisan and the bacterium originally described by Nocard was named as Nocardia farcinica. In 1891, another similar bacterium (Nocardia asteroides) was isolated by Eppinger from a human brain abscess. Initially it was thought that they are the same bacteria. On the basis of the genetic differences the separate entity was established later.

The re-examination of Nocard’s original isolate revealed the existence of two different filamentous bacteria i.e. Mycobacterium and Nocardia. The cause of ‘bovine farcy’ has been subsequently attributed to Mycobacterium. Later, it is proved that Mycobacterium farcinogenes is the actual causative agent of ‘bovine farcy’.

The basic processing and preservation techniques such as canning, freezing, dehydration, salting, pickling and freeze drying are designed to change perishable foods into more usable form and prevent undesirable changes caused by microorganisms, or by chemical, physical and biochemical reactions in the food itself. Hence an ideal processing technology would involve prevention of growth of microorganisms and at the same time retention of f lavor, texture, nutritive value and palatability of the products.

Processing and Preservation

Processing and preservation is the best way of utilizing surplus production of fruits during seasonal gluts.

Several fruits and vegetables are unexploited for proper utilization and product development. Due to lack of utilization, there is a lot of wastage and ultimately the great loss to the people as well as nation. Some unexploited fruits and vegetables have potential for introducing new products. Therefore unexploited fruits and vegetables have to be exploited for new product development especially from underutilized sub-tropical and tropical fruits and vegetables. Research and development should be undertaken to utilize these fruits and vegetables.

Unexploited Fruits

Unripe Green Mango: Although pickles are prepared but droped green mango fruits are not preferred for pickle preparation. They can be dried and utilized for preparation of dried slices or amchur. Amchur is used to develop flavor and taste in Ice cream. These products are used to develop flavor and taste in meal or food. It is also used to prepare chatney. But utilization of Amchur is not known to common people.

Avocado: It is found in tropical and sub-tropical climatic regions having more humidity and rainfall. In Ethiopia it is found throughout the country but not utilized properly by people. They prefer to eat ripe fruits with salt and lime juice. It is very healthy fruit for chronic disease like cardiac and diabeted diseases. This is seasonal use but no product is available for off season. Therefore researches should be carried out for different products development of Avocado products.

Of the 7 billion global population, about 800 million do not have enough food to eat and majority of the them live in developing countries. By 2050, the world population is estimated to reach 9 billion. Plant pests and diseases are responsible for losses of 20 to 40% of global food production. Due to increasing global trade and a changing climate, plant diseases pose a major threat to food security today than ever before. Agriculture will have to cope with weather fluctuations that can affect the survival, distribution and multiplication of plant pathogens apart from shift in pathogenic microbial flora. Emergence of new races of pathogen potentially threaten the production of food. To cite an example, migration of 13 -A2 clonal lineage of Phytophthora infestans from Europe, during 2013, devastating tomato and potato in India. Plant pathogens also impact on environment sustainability, forest health, recreational horticulture, human and animal health.

The science of plant pathology can play a much needed role in alleviating hunger and malnutrition through development of affordable solutions for devastating plant diseases leading to increase in food production. It hold promise to ensure quality produce by containing microbial invasions and toxin contamination of food crops. Plant Pathologists have an important role to play in meeting the food security need of the nation by developing technologies for ensuring proper crop health. There is an urgent need to produce more food per unit area for feeding rapidly increasing human population. We need to act ahead of pathogens in our efforts to ensure normal crop yields. Cutting edge biotechnologies such as CRISPR gene editing systems and RNA interference are being exploited to rapidly developed crop varieties having resistance to specific pathogen races.

Crop protection has come a long way from predominantly chemical based approaches to more environment friendly IDM technologies including green chemistry. There is a need to develop bio-intensive modules for management of diseases. Decision support system need to be developed for important diseases for their timely, more efficiently management. There is need to adopt information technology at a larger scale to facilitate quick dissemination of new crop protection solutions among the farmers and other stakeholders.

Definition

Pathogenesis can be defined as the chain of events leading to the development of a disease. In another words it is also called disease cycle.

It tells us about

The Disease Triangle and Disease Pyramid

The disease triangle is one of the first concepts encountered by students in an introductory plant pathology course and often may be encountered in higher level classes. The interactions of the three component namely (1) susceptible host (2) virulent pathogen and (3) favorable environments have been visualized as a triangle, generally referred to as the “DISEASE TRAINGLE”. Each side of the traingle represent one of the three components. The length of each side is proportional to the sum total of the characteristic of each component that favor disease. For example, the more virulent and abundant the pathogen, the longer the pathogen side would be and the greater the potential amount of disease. Similarly if the plant are resistant, the widely spaced or wrong age, the amount of disease would be small or zero. Where as if the plants are susceptible, at a susceptible stage of growth, or densely planted, the host side would be long and the potential amount of disease could be great. Also, the more favourable the environmental conditions that help the pathogen, or that reduce host resistance, that longer the envirnmental side would be and greater the potential amount of diseases. If the three component of the disease traingle could be quantified, the area of the traingle would represent the amount of disease in a plant or in plant population. If any of three component in zero, these can be no disease.

Definition

Plant disease in which no pathogens or parasitic is associated with the cause is known as Non-parasitic disease. They are also called as noninfectious or physiological disorders.

General Characteristics

Occurs in the absence of pathogen and therefore, cannot be cultured or transmitted.

Caused by the lack or excess of something that supports life from diseased to healthy plants.

Effect plant in all stages of their lives, such as seeds, seedlings, mature plants or fruits.

Symptoms may range from slight to severe & affected plants may even die.

These disease cause damage in field, in storage or at the market.

Introduction

Plant pathogens induce diverse reactions in the body of their hosts. This result in creation of abnormalities which become visible on the plants. A visible or otherwise detectable expression of abnormal physiology, development, or behaviour in a plant resulting from disease is called symptoms. Normally, a distinction is made between symptoms and signs A symptom of disease is expressed as a reaction of the host to a causal agent, whereas, a sign is evidence of disease other than that expressed by the host. Signs are usually the structures of the pathogen. A disease is first noticed by the presence of symptoms and /or signs, and recognition of specific type of symptoms or sign aid in the eventual diagnosis of the disease.

Definition

To make a healthy plant sick or diseased, primary requirement of a pathogen is spread of its inoculums from the source of survival to the susceptible host. The spread of a plant pathogen within the common area in which it is already established is called dispersal or dissemination. Moving the inoculum only a few inches and transporting it for hundreds of kilometers both represent its dispersal. Nevertheless, the pathogen dispersal is not necessarily only for spread of diseases but also for continuity of the life cycle and development of the pathogen. A detail knowledge of pathogen dispersal is necessary to find out effective control measures for diseases because the possibilities of preventing dispersal and thereby breaking the infection chain always exist.

A. Types of parasitism

An organism that lives within or upon another living organism from which it derives nourishment and in which it may cause various degrees of injury is called as parasite. The removal of food by a parasite from its host is called parasitism. Among the parasite one can distinguish different degree of parasitism

Epidemiology

Vanderplank has called epidemiology the science of disease in population. Epidemiology puts its emphasis on population phenomena. The important populations are those of the host, on the one hand, and of the pathogen, on the other. But further, epidemiology is concerned with host-pathogen interactions that lead to disease and crop losses. These interactions are often environmentally dependent. So epidemiology deals with effects of the biotic and abiotic environments. Finally , man has had important effects on hosts, pathogens and the environments, effect that today are increasing in magnitude and scale of importance. Epidemiology therefore also deals with the effects of man on disease and sometimes with the effects of plant disease on mankind. All of this can be symbolized by the disease tetrahedron.

The techniques used in disease management mainly based on two principles: Prevention or prophylaxis and cure. The first principle prevention includes disease management tactics applied before infection i.e., the plant is protected from disease. It includes: avoidance, exclusion, eradication, resistant & protection. Second principle curative action: functions with any measure applied after the plant is infected i.e., the plant is treated for the disease. It includes therapy.

Definitions

Selection, integration and implementation of disease control means on predicted economic, ecological, and sociological consequences.

A comprehensive approach to disease control that uses combined means to reduce the status of diseases to tolerable levels while maintaining a quality environment.

The optimization of disease control in an economically and ecologically sound manner, accomplished by the coordinated use of multiple tactics to assure stable crop production and to maintain disease loss below the economic injury level while minimizing risks to man and the environment.

A sustainable approach to manage diseases by combining biological, cultural, physical and chemical tools in a way that minimizes economic, health and environmental risks.

Crops are grown with the primary aim of maximizing the profit for the cultivators. To achieve this goal, high yielding cultivars and suitable agricultural practices are selected. But due consideration is not given for the levels of susceptibility of the cultivars and some of the agricultural practices may enhance the chances of disease incidence and consequent losses. Hence, it becomes obligatory to determine the effects of crop cultivar and agricultural practices on the extent of disease incidence and to assess losses caused by microbial pathogens in different crops in an agroecosystem. Crop losses reflect the effects of various factors such as use of disease resistant cultivars, application of chemicals, biocontrol agents and preventive measures to reduce inoculum levels, introduction of new diseases and restriction of disease spread. Assessment of crop losses is essential to choose the most effective short- and long-term strategies of disease management. Disease assessment enables the plant pathologists is to gather quantitative information for evaluating disease management strategies, for undertaking surveys of losses and breeding for disease-resistant cultivars.

Fungal and bacterial pathogens infecting either directly or causing secondary infection of inflorescence may be responsible for greater losses than the pathogens infecting stems or foliage, if they do not cause the death of plants. The extent of earhead infection by the pathogen(s) is directly correlated to the quantum of yield losses.

Postharvest diseases caused by fungal pathogens are more numerous than those due to bacterial pathogens. Infection by these pathogens may be initiated in the field before harvest, during transit or storage. These pathogens may remain dormant and become active, when the physiological conditions of the produce and environmental conditions become favourable. Symptoms characteristic of the diseases are observed as the produce age or ripen.

INTRODUCTION

Providing access to the nascent information is the main motto of the library. Electronic resources management (ERM) is the latest phenomenon in the field of Library and Information Science. In a nutshell it is responsible for the evaluation, selection, pricing, securing, maintenance and provision of electronic resources to the users. As electronic resource collections continue to expand, allied workflows and processes encompass growth in complexity. Advances in printing technology and information communication technology (ICT) have resulted in transforming the publishing industry into e-publishing. It has resulted in considerable impact on the library collection building process in terms of print collection, electronic and online resources.

Now a days many reputed publishers have started e-publishing and many of them are now issuing their publications in electronic version besides conventional printing. The libraries are upgrading their collection in terms of documentary resources and electronic resources and infrastructure to sustain in the fast moving knowledge society.

INTRODUCTION

Library and information centers are primarily service institutions which are expected to provide information to the entire satisfaction of user groups. However, in recent times, it is observed that there is conglomeration of several services in a pin-pointed manner in which the libraries are facing problem of confusion. Therefore, leading library and information centers have started adopting emerging management principles and practices in their functions and operations. Among all these new traits of management the concept of quality management appears to have a dynamic impact upon the improvement of organizational objective and functions. Since agriculture libraries are vibrant information organizations their quality of services needs to be improved in the modern technological era. The application of Total Quality Management (TQM) is one of the vital aspects of the management techniques that appears to be very much applicable and can bring about a great transformation in quality of library services. The present paper makes an analytic discussion on the applicability of TQM in Agriculture Libraries in India.

INTRODUCTION

The phenomenal growth and reach of World Wide Web (www) has been one of the most significant developments in the last few years. It has rapidly gained popularity and has become most widely used application of the Internet. Today, the World Wide Web has emerged as the most powerful medium for information publishing and access. A plethora of information sources.

The user friendly interface and hypertext features of Web have been attracting a significant number of users as well as information providers. The web-based e-services are increasingly being used by research communities as a viable means to access to a plethora of digital resources in networked information environment. Concomitantly, utilization of such electronic methods and means is expanding substantially throughout the chain of e-research and scientific knowledge production.

INTRODUCTION

The term open source describes the practices in production and development that promote access to the end product’s source materials. Open Source Software (OSS) came into existence with the development of ICTs. The services and the collections of the libraries and information centres are becoming global due to the application of Information Communication Technologies. Information can now be accessed from even the remote places with the help of internet. The term “open source” refers to software that includes the original source code, used to create it so that users can modify it writing to their requirements.

It also includes the right of redistribution; therefore, there may be products that are based on other open source products. While the software may be free, a developer or distributor may charge for services such as special programming, installation, training and technical support, etc. In general, the source code of OSS is widely accessible, freely available and reusable. Now the institutions especially the academic institutions are starting to build their own repository to serve their community locally and globally.

RISE OF INFORMATION INDUSTRY

Market place created by the convergence of computers, telecommunication and microelectronics. The whole business is depend on marketing, therefore marketing of any product is the whole business seen from the point to point of view of its final result, that is from the customers point of view. Thus marketing means art of selling of working with market to actualize potential exchanges for the purpose of satisfying human needs and wants. It is the systematic gathering, recording and analysis of data about problems relating to the marketing of goods and services.

GLITCH IN INFORMATION INDUSTRY

Today information industry is a buss word every day user vista is opening. Some companies believe there are no new opportunities. They believe this information industry in mature that they are selling a commodity. But there is no such thing as a mature market or a commodity. It’s only getting in the way of imagination. Starbucks didn’t see the coffee market as mature.

Lateral marketing is to think of product in relation to another product service or idea. Through the thinking across two products rather than cereals plus a snack. Instead of putting loose cereal in a box, they use the cereal in the from of a snack bar that can be carried and eaten any time. This health bar suddenly people are able to consume cereal any time of the day in a conrenient form.

Marketing Guru Philips Kotler defines marketing as the analysis, planning implementation and control of carefully formulated programmes, designed to bring about voluntary exchanges of values with targets, markets for the purpose of achieving on designing the organization offering in terms of target markets need and desired on using effective pricing communication and distribution to inform, motivate and service the markets. Marketing brings in an element of competition. This will result in providing better services.

INTRODUCTION

‘Society’, this word is derived from the Latin word ‘socius’ which literally means a companion. Society is complex organism constituted by persons bound in willing allegiance to some common standards of psychological approach and outward behavior [10]. The story of libraries reflects the social, economical, cultural and educational needs to which libraries have responded. In preliterate society, human beings depended on live memory and the spoken words. By 2700 BC, the Sumerians had established private and government libraries for preserving their varied writings for use in the form of clay tablets. Ancient Egypt, from where writing was developed, produced some libraries which were composed of papyrus rolls [11]. So we can see, from the very initial stage of the society; books, papers, manuscripts, drawings, copper plates and other articles were being presented to it by various sources. We know that there is close relation between books and society. Healthy society is the creation of sound mind by books. Without sound mind, social progress can not be achieved properly. Every significant book may reflect distinct period of history. It is not essential to say that an author and his works can create new culture and lead to social changes. The books of authors of different countries in the world had / have a long influence on society [3].

In this present era, literature and knowledge is growing very fast and for their proper collection, preservation and to properly disseminate to people, we need public libraries. Society always depends on smooth growth and this growth is neither willful nor arbitrary[10]; it is consistent and systematic. For smooth and systemic growth of society, the government of different countries and states in the world have established schools, colleges and universities. No doubt, the government, different organizations, industrialists have to give priority to drinking water, sanitation and other conveniences. On the other hand, to remove illiteracy or to educate the citizens/nations and to introduce the human beings with phenomenal explosion of knowledge and information, government and other reputed agencies have established and also are establishing public libraries whose services play a vidal role in national progress and development.

Water used for irrigation contain some salts, but quantities and kinds vary greatly depending on the source of water. Since sodic status of soils can be greatly influenced by salts in irrigation waters, successful irrigation practices require the evaluation system to judge irrigation water quality and methods employed. The actual damage done by salt to plants or soils depends on the concentration in soil solution rather than the quality of irrigation water applied. Thus, the use of some water source for irrigation might lead to severe salt problem in soils where drainage is restricted.

Criteria for evaluation of irrigation water

Various criteria considered in evaluating the quality of irrigation water are:

1. Salinity hazard

The most satisfactory method for rating the salt content of irrigation water involves measuring electrical conductivity. Various conductivity limits have been proposed to indicate the degree of salinity problems that might be anticipated with use of irrigation water on crops. There are four classes of salinity hazard such as C₁, C₂, C₃, and C₄.

Trees are an integral and indispensable constituents of our natural surroundings. The trees keep the environment clean, make the soil healthy and provide food, fibre and shelter to mankind and wild animals. Trees help in stabilizing the soil, a vital natural resource, prevention of soil and water erosion, control run off water in the catchment areas, acts as a shelter belt against wind erosion in arid zone, act as a wind breaker to protect the coastal region during storm and cyclone besides contributing substantially to economic development. The National Commission on Agriculture stress the need for afforestation of about 40 million ha of land presently lying barren because of salinity, sodicity, waterloggings, ravines, coastal sandy areas, stony and gravelly lands, high altitude and slopping lands. Several agencies in various parts of the country are engaged in afforestation of these degraded lands.

Beverage is a drinkable product which includes all drinks fermented or unfermented, sweetened or unsweetened. It may be fruit based or non-fruit beverage. Fruit based beverage is the fruit juice that has been considerably altered in its composition before consumption e.g. drink, squash, nectar etc. In this chapter, preparation of RTS drink and squash has been discussed.

1. PREPARATION OF READY-TO-SERVE (RTS) DRINK FROM FRUITS

Theory: RTS is a type of fruit beverage which contains at least 10% of fruit juice and 10 degree Brix as Total Soluble Solids (TSS) with 0.3% acidity. It is not diluted before serving, hence it is known as ready-to-serve beverage. It can be prepared from fresh/preserved pulp/juice of various fruits like mango, litchi, apricot, guava, lemon etc.

In recent years, oilseed crops are being increasingly exploited for production of pharmaceuticals, surfactants, plasticisers, emulsifiers, detergents, lubricants, adhesives, cosmetics, oleo-chemicals, biofuels apart from their demand for their healthy vegetable oils and livestock feeds (Metzger and Bornscheuer, 2006). The increased interest resulted in an 82% expansion of oilseed crop cultivation areas and about a 240% increase in total world production over the last 30 years (Rahman and Jimenez., 2016).