eChapters

Q. 1 The amount of heat required to raise the temperature of 1gm milk by
one degree celsius in comparison to water is
(A) 85 %     (B) 93 %
(C) 107 %    (D) 100 %

Abstract

Thermal properties of food are its ability to conduct, store and lose heat. These properties are inherent in food processing and preservation practices. Thermal properties are important for modelling processes, engineering design of processing equipment, sterilization and aseptic processing. Important thermal properties are thermal conductivity, specific heat and thermal diffusivity. These properties depend on chemical composition, water fraction and temperature.

Introduction

Thermal properties are involved in almost every food processing operation. It is essential to have knowledge of thermal properties of foods which is important in analysis and design of various food processes and food process equipment involved in heat transport. Thermal properties of food are greatly depending on composition, temperature and density of food. Thermal properties required for heat transfer calculation include specific heat, enthalpy, thermal conductivity and thermal diffusivity. Thermal properties of foods are related to heat transfer control in specified foods and can be classified as thermodynamic properties (enthalpy and entropy) and heat transport properties (thermal conductivity and thermal diffusivity). Thermo physical properties not only include thermodynamic and heat transport properties, but also other physical properties involved in the transfer of heat, such as freeze and boiling point, mass, density, porosity, and viscosity. These properties play an important role in the design and prediction of heat transfer operations during the handling, processing, canning, storing, and distribution of foods.

Temperature stands as a fundamental environmental factor profoundly influencing the life cycle of crops, from the initial spark of germination to the final stages of maturation and yield formation. The thermal regime, encompassing the daily and seasonal patterns of temperature, dictates the rate of biochemical reactions within the plant, thereby governing the pace and efficiency of physiological processes crucial for growth and development.
This chapter, „Thermal Regime: Crop Growth and Development,“ will delve into the intricate relationship between temperature and the various phenological stages of crop plants. It will be explored how different cardinal temperatures – the minimum, optimum, and maximum thresholds – dictate the boundaries within which growth can occur and the rates at which developmental milestones are achieved. Understanding the impact of temperature on processes like photosynthesis, respiration, nutrient uptake, and ultimately, yield, is paramount for optimizing crop production in diverse environments.
Furthermore, we will examine the concepts of heat units or growing degree days, which provide a quantitative framework for predicting crop
development based on temperature accumulation. By appreciating how the thermal environment interacts with genetic potential and other environmental factors, we can gain valuable insights into crop suitability for specific regions, the timing of critical growth stages, and strategies for mitigating the adverse effects of temperature extremes.
This chapter aims to provide a comprehensive understanding of the thermal regime and its critical role in shaping the growth and development of our cultivated plants, laying the foundation for informed agricultural practices and improved crop management.

Temperature stands as a fundamental environmental factor profoundly influencing the life cycle of crops, from the initial spark of germination to the final stages of maturation and yield formation. The thermal regime, encompassing the daily and seasonal patterns of temperature, dictates the rate of biochemical reactions within the plant, thereby governing the pace and efficiency of physiological processes crucial for growth and development.
This chapter, „Thermal Regime: Crop Growth and Development,“ will delve into the intricate relationship between temperature and the various phenological stages of crop plants. It will be explored how different cardinal temperatures – the minimum, optimum, and maximum thresholds – dictate the boundaries within which growth can occur and the rates at which developmental milestones are achieved. Understanding the impact of temperature on processes like photosynthesis, respiration, nutrient uptake, and ultimately, yield, is paramount
for optimizing crop production in diverse environments.
Furthermore, we will examine the concepts of heat units or growing degree days, which provide a quantitative framework for predicting crop
development based on temperature accumulation. By appreciating how the thermal environment interacts with genetic potential and other environmental factors, we can gain valuable insights into crop suitability for specific regions, the timing of critical growth stages, and strategies for mitigating the adverse effects of temperature extremes.

Thermal stress arises whenever there is some increase or decrease in temperature of a body which causes either expansion or contraction in the dimension of body. If body is free to expand or contract, with the rise or fall of temperature, there exist no stress in the body. But if deformation of the body is partially or completely resisted then stresses are set up in the body which is known as Thermal Stress. However amount of stress induced in partially prevented deformation will be small than in case deformation is totally prevented.

Polymerase Chain Reaction

The Polymerase Chain Reaction (PCR) technique, invented in 1985 by Kary B. Mullis, allowed scientists to make millions of copies of a scarce sample of DNA. The technique has revolutionized many aspects of current research, including the diagnosis of genetic defects and the detection of the AIDS virus in human cells. The technique is also used by criminologists to link specific persons to samples of blood or hair via DNA comparison. PCR also affected evolutionary studies because large quantities of DNA can be manufactured from fossils containing but trace amounts.

Kary Mullis invented the PCR technique in 1985 while working as a chemist at the Cetus Corporation, a biotechnology firm in Emeryville, California. The procedure requires placing a small amount of the DNA containing the desired gene into a test tube. A large batch of loose nucleotides, which link into exact copies of the original gene, is also added to the tube. A pair of synthesized short DNA segments, that match segments on each side of the desired gene, is added. These “primers” find the right portion of the DNA, and serve as starting points for DNA copying. When the enzyme Thermus aquaticus (Taq) is added, the loose nucleotides lock into a DNA sequence dictated by the sequence of that target gene located between the two primers.

The test tube is heated, and the DNA’s double helix separates into two strands. The DNA sequence of each strand of the helix is thus exposed and as the temperature is lowered the primers automatically bind to their complementary portions of the DNA sample. At the same time, the enzyme links the loose nucleotides to the primer and to each of the separated DNA strands in the appropriate sequence. The complete reaction, which takes approximately five minutes, results in two double helices containing the desired portion of the original. The heating and cooling is repeated, doubling the number of DNA copies. After thirty to forty cycles are completed a single copy of a piece of DNA can be multiplied to hundreds of millions.

2.1 Introduction

The name thermodynamics stems from the Greek words therme (heat) and dynamis (power), which is most descriptive of the early efforts to convert heat into power. It may be defined as the science that deals with the relations among heat, work and properties of a system. Today, thermodynamics is broadly interpreted to include all aspects of energy and energy transformations, including power generation, refrigeration, and relationships among the properties of matter. It is viewed as the science of energy, and thermal engineering is concerned with making the best use of available energy resources.

Thermodynamics basically entails four laws or axioms known as Zeroth, First, Second and Third law of thermodynamics.

The zeroth law deals with thermal equilibrium and establishes a concept of temperature.

The first law pertains to the conservation of energy and introduces the concept of internal energy.

The second law indicates the limit of converting heat into work and introduces the concept of entropy.

The third law defines the absolute zero of entropy.

The concept of energy was introduced by Newton in the field of mechanics during generalizing the hypothesis of kinetic and potential energies. Energy may be defined as the capacity to do work and it is a scalar quantity. It cannot be seen or observed. Its presence can, however, be felt by the properties of the system. There occurs a change in one or more properties of the system in case of energy transfer. The absolute value of energy of a system is difficult to measure, whereas the energy change is rather easy to calculate. Energy follows the conservation law, one of the most fundamental laws of nature, which simply states that during an interaction, energy can change its form from one form to another but the total amount of energy remains constant, that is, energy cannot be created or destroyed only form can be changed.

Direction of rotation can be reversed in
(A) 2- stroke engine           (B) 4- stroke engine
(C) Both (A) and (B)          (D) None of these

Thermodynamics is defined as the “branch of science which deals with the interaction between the heat and work”[1]. Thermodynamics is also sometimes stated as the science of energy. Thermodynamic deals with the principles of energy and energy conversion in engineering. It also considers the thermodynamic properties of substances. Thermodynamics deals with the conversion of heat into work and vice-versa.

1. Introduction

Thermodynamics is science of energy and may be defined as “The branch of science which deals with the Interoction between the heat and work is referred as Thermodynamics

’Thermo’ means heat and ’dynamics’ means motion. It deals with energy interaction when work is converted into heat energy or vice versa. Precisely, thermodynamics may be defined as a science which deals with energy transformation from one form to another and dealing with relationship among the properties ofthe system. In power plants, internal combustion engines, boilers, nozzles, diffusers etc. are the example where heat is converted into work. In compressor, turbine, cooling of engines by water, application of brakes in a vehicle etc. are the examples where work is converted into heat.

Based on the nature and purpose of the content, there are numerous classes of scientific communications. Theses represent the class of research communications that are of great importance to the students. Thesis is part and parcel of the master’s and doctoral programme in almost every academic institution. In some institutions, even the bachelor students are expected to submit their brief report on project.

Chromatography is an important analytical technique for the separation, isolation and identification of the constituents of a mixture. It is a physical method of separation in which the components to be separated are distributed between two phases; one of these phases consisting a stationary bed of large surface area, the other being a fluid that percolates through or along the stationary bed. All forms of chromatography do have the common features given in this definition. All of them involve the physical movements of the sample across a flat surface (tube like) or through a tube. The stationary phases in all of these possess a large surface area. In all the techniques, the movement of the sample is due to the motion of the fluid/mobile phase. The principle underlying all these methods is the selective retardation of the movement of the components by the stationary phase. These methods result in the production of bands of concentrated components. The basis of naming various chromatographic methods are different:

Kirchner was the first in 1950 to think of thin layers. But it was Egon Stahl in 1958 who was responsible for bringing out standard equipment and related procedures to popularize thin layer chromatography (TLC). TLC is a modified form of column chromatography. Hence it is also called open column chromatography. The adsorbent is spread over a supporting material (glass or plastic sheets) to form a thin layer of adsorbent. As a binder, plaster of Paris or gypsum is added to the adsorbent material like silica gel (hence silica gel TLC). The adsorbent is spread over the plate as a thin layer of 0.25 or 0.5 mm. The adsorbent to water ratio is 1:2. It is initially allowed to air dry, followed by drying in an oven at 110oC for 1-2hr or overnight (activation of TLC plates) after which the plate is ready for thin layer chromatography.

Highlights • Banana leather can be enriched with microencapsulated ? – 3 fatty acid for value addition. • Blanching can destroy more than 80% of vitamin C content. • Henderson and Pabis model can better predict the drying kinetics of banana leather. Introduction The ever increasing demand for functional foods having numerous health benefits has been an active research ground for the food scientists around the globe. Till date, many food products have been formulated to deliver functionalities by value addition with bioactive compounds (Carvalho Barros et al., 2020). These products have been extensively studied and proved to be beneficial, especially for elder age group against various metabolic syndrome and health complications. Functional foods are edible products fortified with compounds having additional health and safety benefits such as vitamins, minerals, and bioactive compounds (Granato et al., 2020). One such example of a nutritionally dense food product with the potential of fortification to meet certain health benefits is fruit leather.

One prime fact in research is not to take the matter for granted and do not believe in status quo. This is most critical mindset for creating something new. Even change may be made in existing circumstances with minimum requirements. Here, I may cite my experience while starting research in 1976 for my doctorate program on immunity against schistosomiasis. The experimental model was albino mouse where schistosomes, by their nature, develop into blood vascular system of the host hence require a special technique called “Perfusion technique” for retrieval of mature and immature schistosomes. This ‘perfusion technique’ requires use of a “Peristaltic pump” and was followed in some western countries (2). However, No body in India followed this perfusion technique hence recovered schistosomes from mouse or from any other host species by teasing the blood vessels or/and cutting and soaking liver,spleen, kidney, lung pieces in normal saline.

The method described here gives an approximate thioglucoside and isothiocyanates contents in rapeseed meal.

Reagents and Apparatus
    1.    Barium chloride (5% solution)
    2.    Volumetric flask, 600 ml
    3.    Steam bath

Method

To 10 g meal (defatted by soxhlet extraction) add 250 ml distilled water, hydrolyse at 54ºC for one hour and then boil for two hours, keeping volume constant. Filter, retaining filtrate and wash residue three times with 50 ml hot water. Add washings to initial filtrate and make up volume to 600 ml. Precipitate barium sulphate by heating and adding excess barium chloride solution. Leave on a steam bath for a few hours and then filter. Ash in muffle furnace and then weigh precipitate.

1. Introduction

This information is collected and complied by the authors from various websites for the motivation of readers particularly women. In no way it is exclusive and we do not claim accuracy of facts described here. Mere purpose is to disclose the fact that miracles do not happen but they are conditioned to manifest when determinations are reinforced by confidence. Live not to spend the time but to use it to spread your manifestations the world over.

Boundaries

The cavity of thorax (thoracic cavity) is formed like a truncated cone which is compressed laterally in its cranial part and some what wider in its caudal part. The dorsal wall or roof of the thorax is formed by the thoracic vertebrae and the ligaments and muscles connected with them. The lateral walls are formed by the ribs and intercostal muscles and other muscles supporting the walls internally and externally. The floor or the ventral wall is formed by the sternum and costal cartilages along with the ligaments and muscles attached to them. The caudal wall or the base of the thorax is formed by the diaphragm. It slopes craniad and ventrad. It is bound dorsally by the last thoracic vertebra, ventrally by xiphoid cartilage and laterally by the last pair of ribs and the costal arch formed by the union of costal cartilages of asternal ribs. The apex of the cone is narrow, nearly oval or triangular in form and it is directed cranially. The cavity of the apex is bound dorsally by the first thoracic vertebra, laterally by the first pair of ribs and ventrally by the first sternebra along with manubrium sterni. The apex is fully occupied by the longus colli muscle, oesophagus, trachea, vessels, nerves and lymph nodes. The width of the thorax is greatest at the level of ninth ribs. The wall of the thorax is internally lined by the serous membrane which is a part of the pleura.

Thoracic Vertebrae

Ox: Thoracic vertebrae characterized by well developed neural spines, short bodies with capitular facets and transverse processes with tubercular facets for articulation with the ribs (Fig.4.1).

• The thorax is the organ of locomotion due to articulation of wings and legs and is connected with the by neck or cervix.

• Thoracic segments are made up of three sclerites namely, dorsal body plate tergum or nota, ventral body plate sternum and lateral plate pleuron.

• Second and middle tagma which is three segmented, namely prothorax, mesothorax and metathorax. Meso and metathorax which bear wings are called as Pterothorax.

• In the apterygote insects the three thoracic segments are similar in size and structure. In the pterygote insects the thorax is highly modified.

• The prothorax is quite large and is somewhat independent of the other segments. The large shield that covers the dorsal and lateral sides of the prothorax is the pronotum.

• The pronotum is the dorsal sclerite of the prothorax, which can be highly modified in various orders such as the Hemiptera, Blattaria, and Coleoptera. E.g undivided and Saddle shaped in grass hopper, Shield like in cockroach.

• Cockroaches have pronotums that extend forward over the head.

• Scarab beetles and other beetles may also have unusual pronotums.

• Treehoppers have some of the most bizarre pronotums of all insects.

ABSTRACT

The deeply rooted coastal grass Spinifex littoreus (Burm.f.) Merr. is a potent soil binder having capability to form a strong and stable dunes. However detailed features of this species has not been thoroughly studied till date. In this communication, salient morphological features along with different crucial micro-morphological peculiarities have been discussed. The comparative analysis of gradual degradation of population of Spinifex littoreus and native dune vegetation of the coastal belt in East Medinipur of West Bengal and adjacent Balasore district of Odisha are provided, along with different biodiversity indices. Plants were characterized as stout, dioecious, stoloniferous grass upto 90 cm tall, with rigid and sharp spiny leaves. Spikelets in racemes subtended by large bract-like spatheoles which are fascicled into large capitate spiny structures 30-37 cm in diameter. S. littoreus is fairly common along sandy shores and dunes. Plants are useful as a sand binder in unstable coastal dunes ecosystem.

A large number of genetic resources, species, and ecosystems are under severe threat. Many species have gone extinct and many more are being pushed towards extinction. Most of the ecosystems have also gone into what we can call functional extinction. The major factors becoming threats to biodiversity are anthropogenic. Human activities, in essence, are not benevolent for biodiversity to flourish in natural systems. Burgeoning human populations are the root cause of biodiversity destruction. Changing human lifestyles fed by a materialistic economy are further acting as catalysts for the ever-increasing human populations to destroy biodiversity evolved over millions of years amid terrestrial conditions favorable for the origin and prevalence of an astonishing variety of life forms on Earth.

There is hardly any threat to biodiversity due to natural factors except those inherent in the designs of natural evolution. A species at a certain point of time in its evolutionary history is destined to vanish, but the void in nature created due to this loss is filled by the evolution of new life forms. Not only the void is filled, the nature gradually goes on enriching itself 

Introduction

India’s textile sector is one of the oldest industries in the Indian economy, dating back several centuries. The industry is highly varied, with hand-spun and hand woven textiles sectors at one end of the spectrum and the capital-intensive sophisticated mill sector at the other. The fundamental strength of the textile industry in India is its strong production base of a wide range of fiber/yarns, from natural fibers like cotton, jute, silk, and wool, to synthetic/man-made fibers like polyester, viscose, nylon, and acrylic.

Ultrasonography has an importance place in human practice and veterinary f ield especially in canine practice. Since many years two dimensional ultrasound has been used for scanning purposes both in human and animal practice. But the scenario has changed in human practice with development of three dimensional technology and later four dimensional ultrasonography has developed which shows movements of the objects being scanned especially in the case of fetuses. Nowadays it has been common to use these advanced technology in the human practices. Yet these technologies are in the childhood stage in the veterinary field. High cost of 3D/4D ultrasound equipment, operational difficulties in non sedated animals & lack of specific knowledge about the operation of volume scanning hinder the use of this technology in the veterinary field. Better understanding of the different application of these technologies can be made to use in research areas for the better understanding of the abnormalities, post therapeutics as well in the diagnosis of the diseases

Principle of Three Dimensional and Four Dimensional Ultrasonography

Sound waves of frequency higher than human audible frequency usually ranges from 2-13 MHz are used in ultrasonography. Depending upon on depth of tissue from the scanning surfaces frequency is selected. Three dimensional ultrasonography gives three dimensional images of the volume being scanned .it works on the same principle of 2D ultrasonography but ultrasonographic beams are sent different angles to get three dimensional image of object being scanned. Volume information is obtained either directly using 2D array probe or by reconstructing three dimensional volume from a series of continuous or non- continuous 2D images by using software (Fenster and Downey, 2000). An advancement of 3D technology is 4D ultrasound. Four dimensional ultrasound adds the fourth dimension as time and gives a dynamic real-time 3Dultrasonography of the concerned organ with a continuous volume image acquisitioned rendering process. (Khurana and Dahiya, 2004).

1.    I deem it a singular honour to deliver Dr. Sen Memorial Lecture. Dr. Sen, who was both an administrator and a visionary, was instrumental for:

Removal of seeds from dry fruits is known as threshing while that of wet fruits is known as extraction. Threshing involves beating or rubbing the plant material to detach the seed from its pod or fruit. The detached seed is then winnowed to remove chaff, straw and other light material from the seed.

Threshing / extraction methods

1. Mechanical threshing

• Various types of threshing machines with adjustable cylinder speeds are available for extraction of vegetable seeds.
• Care must be taken to avoid damage to the seed during mechanical threshing, by properly adjusting the speed of the beaters, the width of the gap between the beaters and the concave, the airflow and the sieve sizes.

22.1. What?

Threshing is the process of separating grains from the straw or pod by impact, friction or both. Threshing should be done at an appropriate time after harvest. Delayed threshing causes rapid deterioration of the grains, especially during field drying or when the crop is stacked in the field. Improper threshing leads to wastage of grains and reduces the quantity of final marketable produce. After threshing, the produce has to be winnowed to remove lighter materials such as unfilled grains, chaff, weed seeds and straw using a blower, air fan or wind. Winnowing improves the ability of the grain to be safely stored, milling output and quality.

22.2. Methods employed

Traditionally, threshing is done by beating the harvested crop on a threshing floor directly or with a stick. Another traditional method of threshing is to make a bull walk in circles on the grain on a hard surface. In some areas, the harvested panicle with grain is spread on the surface of a country road so that the grain may be threshed by the wheels of passing vehicles. In these methods winnowing is separately performed. However, with the development of technology, now it is mostly done by machine referred to as threshers, shellers and stripper. Some of these threshers have inbuilt facility for threshing. Thus, threshing and winnowing are completed in a single process.

9.1. Origin and distribution

• Originated in Southern Mediterranean.

• Distributed in India, Asia, Australia, Canada, Europe, France, Germany, Greece, Italy, Morocco, Spain, USA

9.2. Economic importance

• Commonly called as common thyme or garden thyme.

• The active principle alkaloid is thymol.

• Constituents - triterpinoid saponins, flavones, ursolic acid (1.5% in tops), coffeic acid, tannins and resins.

• Oil of thyme - colourless, yellow or red liquid with a characteristic pleasant odour, and a pungent taste.

English name : Thyme
Botanical name : Thymus vulgaris L.
Family : Lamiaceae
Chromosome number : 2n = 30
Centre of origin : Mediterranean region
Thyme (Thymus vulgaris Linn.), also known as ‘Common Thyme’ or ‘Garden Thyme’, belongs to the Lamiaceae family and has been a vital herb spice for centuries. The name “thyme” originates from the Greek word meaning “to fumigate” or “thumus,” which symbolizes courage. The herb contains various nutrients, including moisture (7.1%), protein (6.8%), fat (4.6%), crude fibre (24.3%), carbohydrates (44.0%), mineral matter (13.2%), calcium (2.1%), phosphorus (0.20%), iron (0.14%), sodium (0.08%), potassium (0.9%), vitamin A (175 IU), vitamin B1 (51 mg), vitamin B2 (0.4 mg), vitamin C (12.0 mg), niacin (4.9 mg), and a calorific value of 340 calories. Upon distillation, thyme yields Red Thyme oil. Additionally, the herb contains triterpinoid saponins, flavones, ursolic acid (1.5% in tops), caffeic acid, bitter compounds, tannins, and resins. Other wild thyme species, such as T. serpyllum L., T. zygus L. (white thyme), and T. satureioides Coss and Bal, also produce volatile oils. The major compounds in T. zygus and T. serpyllum include thymol, linalool, and linalyl acetate, while T. satureioides contains thymol, borneol, and a-terpineol.

Thyme is one of the best known European culinary herbs. The dried leaves and flowering to ps of Thymus vulgaris Linn. are called Thyme and those of Thymus serpyllum wild Thyme, which is found in the Western temperate Himalayas, from Kashmir to Kumaon hills, India, at an altitude of 1,525 meter above mean sea level. Thyme is grown in Europe, Austria and North Asia. It is now cultivated in France, Germany, Spain, Italy and other parts of Europe and, also, in England, North Africa, Canada and the USA. It is a common garden plant which survives for many years under good culture. The dried leaves are curled, are of brownish-green color, usually no longer than 6-7 mm and 2-3mm broad and marketed in whole or in ground form. The flavor is aromatic, warm and pungent. Wild Thyme is a low, hardy perennial, undershrub, 20-40cm high, successfully introduced into the Nilgiris district of Tamil Nadu, in Southern India, or at higher elevations. It is used both for seasoning and for its volatile oil, ranging from 1.08-2.0% (average 1.0%), and in India, its cultivation on a commercial scale can be tried in the western temperate Himalaya from Kashmir to Kumaon hills between 1500 and 4000 meters above mean sea level. The plant can be grown for ornamental edging along the paths in gardens, and is also suitable for rockeries. Leaves are oblong-lanceolate, 10 mm x 3 mm, with orange-brown glandular dots; flowers are coriaceous, small, lavender, purplish to almost white in color, attractive to honeybees, in pubescent verticillaters (Plants that have their flowers intermixed with small leaves growing in a kind of whirl are called verticillate plants); nutlets are brown in color.

ABSTRACT

Biodiversity is a major resource for drug development. Since ancient times mankind has exploited nature for all kind of useful products and enjoyed the colors, flavors and fragrances of flowers and leaves etc. The current global resurgence in the use of plant based drugs offers an ideal opportunity for the country to emerge as a major player in the herbal products market. Herbal medicines are chemically diverse and may contain thousands of bioactive compounds, which can be of immense value to the pharmaceutical industries. Since ages, herbal medicine has been a major part of traditional knowledge play an important role for identification of biological resources worthy of commercial exploitation. Origanum vulgare L. is a wild plant of Labiatae family grows widely in Ladakh region (11500 to 13000 ft). The local people of this region use this plant for various ailment and culinary purposes due to the potential of active ingredients. The present objective of this study is to isolate the thymol content, a major ingredient of O. vulgare and quantifying the same. The volatile oils were extracted through hydro-distillation and active compound was analyzed by Gas Chromatography (GC-17A Shimadzu). Our results demonstrate that the thymol content of O. vulgare from this region is 80.28% as compared to plants grown at other low altitude regions. It is well known that plants under stress respond with biosynthesis of phytochemicals to enable them to adapt to the harsh environmental conditions. Ladakh being unique in many aspects due to its geo-climatic conditions like high elevation, extreme cold, dry weather and low humidity. Plants surviving in Ladakh therefore have unique chemical composition as compared to those grown elsewhere.

It is a small mass of tissue present on either side of the trachea or windpipe. It is a very important structure that helps in the metabolism of the body.

When the basal metabolism is below normal, a person tends to be slow in his movements. He feels cold more and may have marked dryness of the skin, along with constipation and a tendency to put on weight. His hair is dry, thin, and coarse and the skin appears dry, scaly and thickened. There may be puffiness in the face, especially around the eyes. The tongue is usually large, the pulse is slow and regular, and the patient often complains of vague pains in the back and stiffness in the joints.

Hypothyroidism: It is a condition that results from the insufficient amount of thyroid hormone in the body. The trouble may also develop from pituitary deficiency, but is more likely due to some inborn error of the thyroid gland. The change usually comes gradually and involves the patients personality and also his ability to think.

Hypothyroidism is seen in both sexes, but is more common in women. Most of these are overweight and may complain of heavy flow during menstruation. The heart is often enlarged, and there is high level of cholesterol in the blood stream.

Construction details

They had a total of 36 tanks, and most of them were made of tin. Each tank had a diameter of 6 meters, was 1.2 meters deep, and could hold up to 30 tons of water. Inside these tanks, there was a plastic lining. Additionally, there were 4 to 5 tanks made from bamboo. Bamboo tanks have a shorter lifespan, lasting 1 to 2 years, while tin tanks can last for 8 to 10 years.

Culture details

The species that was cultured over there was Red tilapia. Culture practice was intensive. The nursery-rearing period was 70 days. In the first step, fish were raised from 0.5 grams to 10 grams in a separate tank for 35 days. The second step involved the growth of fish from 10 grams to 30 grams for the next 35 days in another separate tank. The fishes were bought from outer sources and they were all male fishes.

The ITAF participants visited the Anuban Tilapia Floating Cage Culture on the Canoy River situated in the central part of Thailand on 11/10/2023 at 1:30 p.m. The purpose of the visit was to learn about the floating cage culture on a large scale.

Construction Details

The farmer had a total 500 number of cages divided into 5 units i.e. 1 unit contains 100 cages. The dimensions of the floating cage are 7m in length, 5m in width and 2m in depth having an area of 70 m3. The fabrication of the cage was done by using the GI pipes attached to the barrels for buoyancy. The double HDPE netting was done from five sides and on the upper side bird net was fixed as a biosecurity measure. The construction cost of the cage was 140000 baht /cage.

Tillage operations in various forms have been practiced from the very inception of growing plants. Primitive man used tools to disturb the soils for placing seeds. The word tillage is derived from the Anglo-Saxon words tilian and teolian, meaning to plough and prepare soil for seed to sow, to cultivate and to raise crops. Jethro Tull, who is considered as father of tillage suggested that thorough ploughing is necessary so as to make the soil into fine particles.

Cultivation involves management of physical environment to produce a favourable habitat for successful crop production. Primitive man used tools to disturb the soil for placing the seeds. The word tillage is derived from the Anglo-Saxon words tilian and teolian means to plough and prepare soil for seed sowing, to cultivate and to raise crops. Jethrotull who is considered as father of tillage suggested that ploughing is necessary so as to make the soil into fine particles.

Tillage is the mechanical manipulation of the soil either with tools and implements for obtaining conditions ideal for seed germination, seedling establishment and growth of crops.

Tillage includes all operations and practices that are used for the purpose of modifying soil physical characters. Tillage is the most difficult and time consuming operation in crop production. About 30 per cent of the total cost of cultivation goes for tillage operations.

Tillage is the physical manipulation of the soil with tools and implements which, results in good tilth for better germination and subsequent growth of crops.

Tilth is the physical condition of the soil resulting from tillage. Soil is said to be in good tilth when it is mellow, friable and adequately aerated. Tilth is dynamic. Mechanical forces may change the roughness of the soil surface, the total porosity and bulk density of the tilled layer and the aggregate or clod size. Heavy rainfall and high velocity wind or water destroys the tilth. The action of wetting and drying, freezing and thawing regenerates desirable tilth. The roughness of the soil surface is an index of the amount of water that can be stored in soil depressions and may also be related to the resistance of the soil surface to sealing. Roughness may be related to rate of evaporation, transfer of heat and air between the soil and atmosphere.

Tillage is a mechanical manipulation of soil to provide favourable condition for crop production. Soil tillage consists of breaking the compact surface of earth to a certain depth and to loosen the soil mass, so as to enable the roots of the crops to penetrate and spread into the soil. A good seedbed is generally considered to imply finer particles and greater firmness in the vicinity of seeds. The depth up to which tillage operations disturb the soil can classify the operation as shallow, medium or deep. The depth of tillage depends on the crop and soil characteristics and also on the source of power or energy available. The optimum seedbed preparation for raising upland crops, involves the many unit operations. Strength of soil is affected by soil moisture content and can be represented in terms of cone index. Compacted soil has more cone index than the loose soils. Movement of machine in the field causes soil compaction. Sometimes it forms hard pan which is to be broken by the tillage operations to enhance root growth and penetration and infiltration of excess water.

Tillage operations are the basic operation, which need to be performed at proper moisture and temperature condition (climatic factor) to attain high degree of germination and better plant growth. Tillage may be defined as mechanical manipulation of soil for the purpose of germination and plant growth but it also does the followings:

Tillage management and seedbed preparation is crucial for crop establishment, growth and ultimately, yield. Typically, the aims of cultivation are to incorporate crop residue, bury weeds and loosen soil to allow appropriate soil–seed contact, easy flow of nutrients, air and water and unimpeded root penetration and crop growth (Hermawan and Bomke, 1997; Bengough et al., 2006). The use of tillage to prepare seedbeds and the subsequent benefits are well documented. However, the amount of tillage and best practice in terms of optimumsoil physical properties specifically for the establishment period has received less attention in comparison. The influence of a seedbed can vary greatly in terms of soil aggregation and subsequent porosity. This soil arrangement, therefore, has direct impacts on soil temperature, water content, oxygen availability and strength, all of which have the potential to affect the performance of the seedbed and its ability to provide an adequate environment for crop establishment. In a review, Braunack and Dexter (1989) stated as summary of previous works conducted on soil aggregation that aggregates will exhibit differing physical and chemical properties depending on the size of the aggregates, thus influencing the suitability of a seedbed for germination, emergence and root development, by influencing factors such as intra- and inter-aggregate aeration. Schjønning and Rasmussen (2000) found that cultivation methods can have large impacts on surface soil layers, altering both strength and pore dynamics (air and water filled), which can restrict plant growth. The relationship between soil physical properties and the plant root systems are vitally important in this process since they directly affect seedbed quality (Awadhwal and Thierstein, 1985; Aubertot et al., 1999; Dexter, 2004).

It is a mechanical manipulation of soil to provide favourable condition for crop production. Soil tillage consists of breaking the compact surface of earth to a certain depth and to loosen the soil mass, so as to enable the roots of the crops to penetrate and spread into the soil.

Tillage operations following primary tillage which are performed to create proper soil tilth for seeding and planting are secondary tillage. These are lighter and finer operations, performed on the soil after primary tillage operations. Secondary tillage consists of conditioning the soil to meet the different tillage objectives of the farm. These operations consume less power per unit area compared to primary tillage operations. Secondary tillage implements may be tractor drawn or bullock drawn implements.

Tillage

The mechanical manipulation of soil with tools and implements for obtaining conditions ideal for seed germination, seedling establishment and growth of crops is known as tillage. Tillage may be described as the practice of modifying the state of the soil in order to provide conditions favourable to crop growth.

Tillage is a common agricultural practice that involves preparing the soil for planting crops. It is the manipulation of soil to create a suitable seedbed, manage weeds, and improve soil structure for optimal crop growth. Tillage methods can vary widely and are often classified into different types based on their intensity and purpose. Here are some common types of tillage:

1. Conventional Tillage: This is the most intensive form of tillage and involves turning over the soil completely, often using a plow. It disrupts the natural soil structure and exposes the soil to erosion but can effectively control weeds and prepare a clean seedbed.

2. Reduced Tillage: Also known as conservation tillage, this method aims to disturb the soil as little as possible. It typically involves minimal or no plowing and relies on techniques like no-till, strip-till, or zone-till. Reduced tillage helps to maintain soil structure and reduce erosion while conserving moisture.

3. No-Till: In this approach, the soil is left undisturbed, with crop residues from previous harvests left on the field surface. A planter creates small openings in the soil for seeds. No-till farming helps retain moisture, reduce erosion, and maintain soil health. It is widely adopted for its conservation benefits.

1. Introduction

With the fairly recent advent of inexpensive, rapid sequencing technologies that continue to improve sequencing efficiency and accuracy, many species of animals, plants, and microbes have annotated genomic information publicly available. It is important to use this genomic information for the identification and isolation of novel and superior alleles of important genes from gene pools of the organisms

Introduction

It is a very important chapter as many questions are asked in competitive examination based on time and work relationship. This topic deals with the simultaneous performance involving the efficiency of an individual or a group and the time taken by them to complete a piece of work. Work is the effort applied to produce a deliverable or accomplish a task. A certain amount of time (T) is taken to complete a certain work (w). The number of units of work done per unit time is called the rate of work (R).

Hence, Work (W) = R x T

Whenever some work is done, the total work itself can be taken as one unit. Hence, we assume the total work done as one unit in the problems we encounter in order to simplify the computations. In these cases, R = 1 / T or T = 1 / R. In other words, R and T are inversely proportional as R T = W, which is a fixed quantity.

Abstract

No one is born with the gift of good time management skills and it is rarely taught at schools or universities. The ways to manage time and get the things done is something which has to be developed and implemented by an individual himself. We need to find out the perfect method that will suit us. We may often wish to get more time but we only get 24 hours, 1,440 minutes or 86,400 seconds each day. The perfect ways to utilize time depends upon skills learned through self analysis, planning, evaluation and self control. Establishing a time management depends on individual’s personality, ability to self motivate and level of self discipline. The objective of this chapter is to focus on benefits of time management, tips for time management, steps for time management and various techniques of time management. The study is supported by case studies which will help in understanding the chapter thoroughly.

Duration: 60-75 minutes
Objective: Master techniques to prioritize tasks, meet deadlines, and reduce stress for improved productivity and work-life balance.
Why It Matters
Effective time management ensures focus on high-impact tasks, reduces procrastination, and prevents burnout. Poor time management leads to missed deadlines, stress, and lower quality work. For example, spending hours on emails instead of strategic planning can derail priorities. This module provides tools to optimize time usage.
Learning Outcomes: By the end of this module, participants will:
1. Understand prioritization and planning techniques (e.g., Eisenhower Matrix, Pomodoro).
2. Practice strategies to minimize distractions and delegate effectively.
3. Create a personalized time management plan.